background image

   

6   

STEP   2   Configure   the   Instrument   Track   Mode   

15.

 

Press   Menu.   

16.

 

Use   the   arrow   keys   or   the   navigation   wheel   to   select   

Track   CH1/CH2

.   

17.

 

Press   Enter   to   enter   the   submenu.   

18.

 

Use   the   arrow   keys   or   the   navigation   wheel   to   select   

Track   On

.   

19.

 

Press   Enter   to   activate   the   track   mode.         See   an   example   of   track   mode   front   display   below.   
   

   

STEP   3   Turning   on   the   Output   

20.

 

Press   Output   On/Off   to   turn   on   the   output.      Now   varying   the   voltage   on   channel   1   or   the   
channel   2   voltage   will   change   the   other   channel   by   the   desired   ratio.   

   

Remote   Operation   

   
The   following   SCPI   command   example   sets   CH1   voltage   output   to   10V,   the   current   limit   to   1.5A,      CH2   
voltage   output   to   track   half   of   CH1’s   value,   or   5V,   the   current   limit   to   1.5A,   enables   the   track   mode   and   
turns   the   output   on.      
   

*RST   
INST:SEL   CH1   
SOURCE:VOLT   10V   
SOURCE:CURR   1.5A   
INST:SEL   CH2   
SOURCE:VOLT   5V   
SOURCE:CURR   1.5A   
INST:COM:TRAC   
SOURCE:OUTP   ON   
…   
<the   following   example   steps   CH1   voltages   from   
2V   to   10V   at   2V   increment.      Observe   CH2   
voltage   varying   from   1V   to   5Vat   1V   increment   
on   the   front   panel>   
INST:SEL   CH1   
SOURCE:VOLT   2V   
..<delay>   
SOURCE:VOLT   4V   
..<delay>   
SOURCE:VOLT   6V   
..<delay>   
SOURCE:VOLT   8V   
..<delay>   

Summary of Contents for Series 2200











Reviews: