C-7
IBM PC/XT/AT or Compatible
with CEC PC<>488 Interface
and ASYST Software
Introduction
ASYST contains analysis, graphing, and data acquisi-
tion software in three integrated modules. Minimum
requirements for ASYST include:
¥
IBM PC/XT/AT or 100% compatible (including
PS/2, 386 or 486-based computers in real mode)
¥
DOS 2.0 (DOS 3.0 or above recommended)
¥
Intel 8087, 80287, or 80387 math coprocessor
¥
640K RAM
¥
25-pin parallel port
¥
Hard disk and one ßoppy
¥
IBM CGA, EGA, VGA, or 100% compatible; Her-
cules monochrome graphics
¥
LIM (Lotus/Intel/Microsoft) expanded memory is
recommended
For this example, an optional software module is re-
quired for IEEE-488 interfacing. The computer must
also be equipped with a CEC interface card (PC<>488
Model 300 or 310, or 4
×
488).
The ASYST program listed here sends a command
string from an IBM computer to the Model 7001 and
displays the response for queries on the computerÕs
CRT.
Directions
1. Using the front panel menu, set the primary ad-
dress of the Model 7001 to 07.
2. With the power off, connect the Model 7001 to the
IEEE-488 interface card installed in the IBM com-
puter.
3. Boot ASYST software. Enter the Main ConÞgura-
tion Menu: use the <F2> key from the OK prompt,
or select CONFIG from the menu bar.
4. In addition to the usual conÞguration require-
ments of ASYST, the GPIB must be conÞgured.
From the Overlay ConÞguration menu, select
GPIB from the Available Overlays list; then select
GPIB Master and Type 1 NEC GPIB driver from the
pop-up menu.
5. From the GPIB ConÞguration menu, select a bus
number, the board number for a Capital Equip-
ment PC<>488 (NEC uPD7210 type), a primary ad-
dress (0), the hexadecimal I/O address (2B8, also
known as the memory address), and an unused in-
terrupt line.
6. Save your changes and return to the OK prompt or
the menu bar.
7. Use the command line editor to enter the example
program. From the OK prompt, type EDIT
7001.DMO; from the menu bar, select EDIT and
type 7001.DMO. Save the program and exit the ed-
itor.
8. When prompted, load the program with the L key,
or type LOAD 7001.DMO from the OK prompt.
9. When the program loads properly, type MAIN
from the OK prompt to start execution.
10. Type in the desired command string at the ÒEnter
command string:Ó prompt. For example, to close
multiplexer channels, type in :CLOS (@1!1:1!5) and
press the return key. The Model 7001 will show
closed channels on card 1. To query for closed
channels, type in :CLOS:STAT? and press the re-
turn key. The Model 7001 closed channel list will
then appear on the computer display.
11. Type <Control-Break> to exit the program loop of
7001.DMO and return to the OK prompt. The pro-
gram-deÞned words can be removed from the
ASYST dictionary by typing FORGET 7001.
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com
Summary of Contents for 7001
