Keithley 2000-Scan Instruction Manual Download Page 16 | Manualshive

Page: 16 / 86

background image

Unpacking and inspection

Inspection for damage

The Model 2000-SCAN is packaged in a re-sealable, anti-static bag to protect it from damage

due to static discharge and from contamination that could degrade its performance. Before
removing the card from the bag, observe the precautions below on handling.

Handling precautions

•

Always grasp the card by the side edges and covers. Do not touch the board surfaces or
components.

•

When the card is not installed in a multimeter, keep the card in the anti-static bag, and
store it in the original packing carton. After removing the card from its anti-static bag,
inspect it for any obvious signs of physical damage. Report any such damage to the ship-
ping agent immediately.

Shipment contents

The following items are included with every Model 2000-SCAN order:

•

Model 2000-SCAN Scanner Card

•

Model 2000-SCAN Instruction Manual

•

CA-109 test lead set for output connections (two red, two black)

•

Additional accessories as ordered

Instruction manual

If an additional Model 2000-SCAN Instruction Manual is required, order the manual pack-

age, Keithley part number 2000-SCAN-901-00. The manual package includes an instruction
manual and any pertinent addenda.

Repacking for shipment

Should it become necessary to return the Model 2000-SCAN for repair, carefully pack the

unit in its original packing carton or the equivalent, and include the following information:

•

Advise as to the warranty status of the scanner card.

•

Write ATTENTION REPAIR DEPARTMENT on the shipping label.

•

Fill out and include the service form located at the back of this manual.

1-4

General Information

«
...
14
15
16
17
18
...
»

Summary of Contents for 2000-Scan























































































Reviews:

No comments

Related manuals for 2000-Scan

Brand: Easy@Home Pages: 28

Brand: PAC Pages: 4

Brand: PAC Pages: 4

SX-70 SODR-X-TRACTOR

Brand: Pace Pages: 2

Brand: PAC Pages: 8

Brand: quadient Pages: 2

AcousticDesign AD-S52

Brand: QSC Pages: 4

Brand: iDataLink Pages: 99

Brand: S+S Regeltechnik Pages: 16

Brand: Alpha Arsenal Pages: 15

Brand: Suunto Pages: 5

Brand: Camcar Pages: 6

Brand: Ratio Computers Pages: 16

Brand: inventum Pages: 32

Brand: hepco & becker Pages: 4

Brand: Veho Pages: 37

Brand: Vega Pages: 56

01 29 9 416 497

Brand: BMW Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands