background image

19

Operation of the Unit

4.1.4 Remote control (HSP5-extension)

The HSP5-extension is connected between the COMBIVERT and the operator. It serves
for the remote control of the COMBIVERT. The HSP5-extension is equipped with special
cable drivers. Therefore the use of conventional RS232-cables is not permitted. The last
three digits of the part number indicate the length of the cable in dm (00.F5.0C0-1005, -
1010, -1030 and 1100).

4.1.5 Other operators

In addition to the described operators the KEB COMBIVERT can be equipped with further
operators for special applications (Profibus, Interbus, Sercos, CAN, DeviceNet). You find
further information on that on our home page.

4.2 Keyboard Operation

4.2.1 Parameter numbers and values

When switching on KEB COMBIVERT F5 the value of parameter CP.1 appears.

Principally during a change, parameter values are immediately accepted and stored non-
volatile. However, with some parameters it is not useful that the adjusted value is accepted
immediately. In these cases the adjusted value is accepted and stored non-volatile by
pressing 

ENTER

. When this type of parameter is changed a point appears behind the last

digit.

The 

function key 

(FUNC) changes

between the parameter value and
parameter number.

With  

UP 

and 

DOWN

 the value of the

parameter number is increased/
decreased with 

changeable 

parameters.

By pressing „ENTER“ the adjusted value
is accepted and non-volatile stored.

2
3

5

2
3

7

RS232-cable 3m
PC / Operator
Part number 00.58.025-001D

9pole SUB-D female

PC                            F5-Operator

Housing (PE)

FUNC.

SPEED

START

STOP

STOP

START

ENTER

F/R

Summary of Contents for COMBIVERT F5

































Reviews: