background image

4.1.2  Encoder connection servo motor 7606910-40xx

 WArNING

Adjustment of the measuring system

The measuring system of synchronous motors must be adjusted to the 

respective inverter. Any mis-adjustment may lead to uncontrolled motor 

response or complete failure of the motor.
In order to avoid any risk, the motor must be put into operation only in 

no-load operation, without connection to the system.

Description

View

Pin Nr.

Signal

View of the connector pins of the 

resolver

5
9

1

6

1

R1 (Ref+)

2

R2 (Ref-)

3

S1 (Cos+)

4

S3 (Cos-)

5

S2 (Sin+)

6

S4 (Sin-)

7

GND

housing

Shield

8, 9

Not connected

Figure 12:  Terminal assignment of the resolver plug for servo motor 7606910-40xx

4.1.3  Connection of the brake and temperature monitoring for servo motor 7606910-40xx

Description

View

Pin Nr.

Signal

View of the brake and tempera-

ture connector

4
5

1

2

1

Brake +

2

Brake -

3

Temp. +

4

Temp. -

5

Not connected

Figure 13:  Pin assignment of the brake connection and temperature monitoring for servo motor 7606910-

40xx

39

 CONNECTION

Summary of Contents for 7608000-4001



















































Reviews: