background image

5

3.

Have your plumber or gas company check for
leaks with a soap solution. (NEVER check with  an
open flame!)

Figure 2-4  IFM Control Panel

NOTE: 

It is estimated that half of all service calls made

on Keating Incredible Frying Machine (IFM) result from
an inadequate gas supply. During installation, have a
gas company representative make certain that the fryer
is receiving adequate gas pressure and volume (see
“Installation” or your serial plate on the fryer door).

WARNING

PROPANE GAS MAY EVENTUALLY LOSE ITS
ODOR AND PRECAUTIONS SHOULD BE TAKEN TO
ASSURE THAT IT IS NOT PRESENT EVEN THOUGH
YOU DO NOT DETECT AN ODOR. IF THERE IS ANY
DOUBT, YOU SHOULD CALL YOUR LOCAL
PROPANE GAS SUPPLIER FOR ASSISTANCE.

III OPERATING

FILLING

NOTE:

Before filling the fryer make certain the fryer 

vessel is sanitized, dry and the drain valve is 
completely closed.  Refer to item 19 on page 15 for
location of drain valve.

NOTE: 

We recommend that solid shortening not be

used in an Incredible Frying Machine (IFM)  as they are

not equipped with a melt cycle. If solid shortening is
used, it should be melted prior to filling the fryer vessel.
Damage done by melting solid shortening in the fryer
vessel will void the warranty.

WARNING

BE SURE THE HEAT TRANSFER TUBES ARE
COMPLETELY COVERED WITH OIL BEFORE
SWITCHING THE FRYER ON. IF OIL LEVEL DROPS
BELOW TOP OF HEAT TRANSFER TUBES,
SEVERE DAMAGE TO FRYER AND INJURY TO
OPERATOR MAY RESULT

WARNING

DO NOT MIX HOT OIL AND WATER IN ANY FORM

CAUTION

Oil expands when heated. The “Fill Level” line has
been provided to ensure optimum cooking while
ensuring the safety of the operator. Do not overfill the
fryer vessel. 

See Figure 3-1

Figure 3-1

Fill Level Line

Fill the fryer vessel with oil or MELTED solid shortening
up to the “Fill Level” line.

LIGHTING

WARNING

BEFORE ATTEMPTING TO LIGHT THE FRYER,
MAKE SURE THE GAS CONNECTIONS ARE
SECURE AND HAVE BEEN LEAK TESTED AND THE
FRYER HAS BEEN PROPERLY FILLED WITH OIL.

1.

Turn on main power switch.

2.

Set thermostat to desired setting. (Between
325°F/162.8°C) – (335°F/165.3°C)

3.

Once main power switch is on and the thermostat

Control Panel with concealed thermostat and no timers

Control Panel with timers

Summary of Contents for SERIES 2000


























Reviews: