Keatec Energy T SERIES User Manual Download

Page: 42 / 43

KE 4256-5492 Keatec T Series 10-20kVA PF1.0 208Vac with Internal Battery 7.0 Touch Screen Users Guide English 20181118

This manual is for qualified personnel only

Page 41

6.5

Appendix 5 BAT_T communication port

Definition of port

Connection between the Temperature senator RJ45 port and UPS RJ45 port.

Device (RJ45)

UPS (RJ45)

Description

Pin 1/5

485+ “A”

Pin 2/4

485 - “B”

Pin7

+12Vdc

Pin8

GND

Available function of BAT_T

•

Battery environment temperature monitoring.

•

Charging voltage modulation depending on batteries’ temperature.

6.6

Appendix 6 Optional port

Definition of Male port

：

Instruction:

UPS

Instruction

Pin1

UPS Battery Low

Pin2

AC Power Failure

Pin3

Turn off UPS

Pin4

Common GND

Function 1 description (Optional):

•

Drive the bypass breaker when feedback alarm.

Function 2 description (Optional):

•

Drive the battery breaker when battery voltage low.

Summary of Contents for T SERIES












































Search results

Summary of Contents for T SERIES

Reviews:

Related manuals for T SERIES

Brands by name

Popular brands

Keatec Energy T SERIES, User Manual

Search results

Summary of Contents for T SERIES

Reviews:

Related manuals for T SERIES

Brands by name

Popular brands