manualshive.com logo in svg

KBL megaSun 6900 a deluxe, Assembly Instructions Manual

The KBL megaSun 6900 a deluxe product comes with an exceptional assembly instructions manual that guarantees a hassle-free setup process. Our comprehensive manual, available for free download at manualshive.com, ensures you have all the necessary information to assemble and use this deluxe product effortlessly.

Share
Download
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

37

5.11 Attach hinge caps

10

5.11.1 CLOSE THE BENCH

5.11.2 OPEN THE SIDE PANE

5.11.3 FASTEN HINGE CAPS

• Unpack both hinge caps (left/right) 

 from the box.

• Push the hinge caps 

 onto the guides and fasten 

Ⓑ

 (M6 - SW10).

Ⓑ

10

5.11.4 CLOSE SIDE PANE

5.12 Attach shoulder tanner / 
        right shoulder piece

PH2

5.12.1 OPEN THE BENCH

Attention

The  bench  and  the  bench  pane  can  be 

damaged when it is opened incorrectly.

• Open the tanning device only with the 

bench pane in position (closed)!

5.12.2 FASTEN SHOULDER TANNER / 

           SHOULDER  PIECE

Shoulder tanners 

 or shoulder piece: 

• Carefully  insert  into  the  gap  between  bench  and 

rear wall.

Attention

Do not tilt! Component can be damaged.

• Insert  the  two  front  metal  tabs  and  align  them 

so  that  the  retaining  bolt  (M6x12  -  PH2)  can  be 

screwed in.

PH2

• Also connect plug X24 

Ⓒ

 to shoulder tanner.

Ⓒ

Summary of Contents for megaSun 6900 a deluxe













































Reviews:

No comments

Related manuals for megaSun 6900 a deluxe

VDL Hapro Innergize HP8580 Manual preview
Hapro Innergize HP8580
Brand: VDL Pages: 56

Brands by name

Popular brands

Load more brands