manualshive.com logo in svg

KBL megaSun 6900 a deluxe, Assembly Instructions Manual

The KBL megaSun 6900 a deluxe product comes with an exceptional assembly instructions manual that guarantees a hassle-free setup process. Our comprehensive manual, available for free download at manualshive.com, ensures you have all the necessary information to assemble and use this deluxe product effortlessly.

Share
Download
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

34

5.4.9  PUT ON LOOSELY - FRONT PLASTIC

          CLADDING 

Similar to disassembling step (4.8.2).

Remove all protective fi

 lm!

5.4.10 ESTABLISH CONNECTIONS D1/D2

Similar to disassembling step (4.8.2).

5.4.11 INSTALL EXTERNAL CONTROL PANEL

Similar to disassembling step (4.8.1).

5.4.12 FASTEN FRONT PLASTIC CLADDING

Similar to disassembling step (4.8.2).

5.5 Install bottom components

PH2

5.5.1 INSTALL AND ALIGN AIR CONDITIONER

Similar to disassembling step (4.6.4).

The  air  conditioning  unit  should  have 

a  slight  forward  tilt  and  suitable  shims 

placed under it if required.

5.5.2 FASTEN ELECTRONIC BOX

Similar to disassembling step (4.6.1).

5.5.3 INSTALL ELECTRONIC BOX

Similar to disassembling step (4.6.3).

5.5.4 INSTALL AQUACOOL UNIT 

Similar to disassembling step (4.6.2).

5.5.5 INSTALL THE AROMA DOSE TIN

• Take  out  aroma  tin 

㉒

  from  the  accessory  box 

 

and install in the aquaCool unit. 

 

- Release retaining clip.

 

- Insert aroma tin.

 

- Lock retaining clip.

㉒

• Put the aquaCool canister 

 

and condensate can-

ister 

⑭

 into their place and connect.

• Fasten cable harness D10/D11 -> (4.6.2).

⑭

Summary of Contents for megaSun 6900 a deluxe













































Reviews:

No comments

Related manuals for megaSun 6900 a deluxe

Brands by name

Popular brands

Load more brands