manualshive.com logo in svg

KBL megaSun 6900 a deluxe, Assembly Instructions Manual

The KBL megaSun 6900 a deluxe product comes with an exceptional assembly instructions manual that guarantees a hassle-free setup process. Our comprehensive manual, available for free download at manualshive.com, ensures you have all the necessary information to assemble and use this deluxe product effortlessly.

Share
Download
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

33

5.4.4 INSTALL REAR PLASTIC CLADDING

Similar to disassembling step (4.8.4).

Remove all protective fi

 lm!

5.4.5 FASTEN GUIDE PLATES

• The two guide plates are fastened outside to a box 

with attachments.

LEFT

RIGHT

• Fasten the guide plates to the shoulder pieces (3x 

4,2x9,5 - PH2 each).

PH2

RIGHT

LEFT

5.4.6 FASTEN EXHAUST AIR VENT

• Fasten exhaust air vent 

 (4x M6 x 16 - PH2).

PH2

5.4.7 PUSH THE DEVICE FLUSH WITH THE WALL

5.4.8 PRETENSION THE CANOPY

Similar to disassembling step (4.8.3).

• Set both springs to the factory default (see sticker 

on device feets).

19

PH2

CAUTION

Components are under spring tension

Risk  of  injury  by  the  canopy  dropping 

down. 

• Support  the  canopy  as  long  as  it  is 

not fully tensioned.

Summary of Contents for megaSun 6900 a deluxe













































Reviews:

No comments

Related manuals for megaSun 6900 a deluxe

HAPRO Luxura X10 Owner'S Manual preview
Luxura X10
Brand: HAPRO Pages: 144

Brands by name

Popular brands

Load more brands