background image

13 

 

 

800 Deere Rd

 

Prescott, WI 54021 

Phone: 715‐262‐4488 Fax: 715‐262‐4487

 

www.Kascomarine.com

   

[email protected]

 

 

Repair Contact Form  

 

Kasco requires all Repairs sent in MUST be accompanied by this form and marked to Repairs 
attention. (ex. Attn: Repairs)

 

 

Repairs returned should include upper pump housing or wire basket for Aerators and De‐Icers. These 

parts protect the motor during shipping.

 

 

Kasco is NOT responsible for shipping damage accrued in return shipment.

 

 

It is the responsibility of customer to ship and pay freight to Kasco. 

 

Do not ship float or control panel with unit, unless otherwise instructed 

 

A fee of $60 per hour will be assessed for cleaning excessively dirty units and float disassembly

 

 

Refer to the Owner’s manual for easy‐to‐follow troubleshooting rule out site issue.

 

Note: Contact Information Should be that of the person or company to contact for repair. 

 

Company  

 

First Name 

 

Last Name 

 

Address 

 

City 

 

State 

 

Zip code 

 

Phone # 

 

Alternate Phone # 

 

Email Address 

 

Preferred method of contact (Circle)  

 

        Phone                      Email  

 

Purchase order # 

 

Additional notes for technician.  

 
 
 
 

 

Submersible Pump Information (Complete if 

 

sending unit) 

 

Parts Included (For office use) 

 

Light kit Information (complete if sending lights)  

 

Model #  

 

Model # 

 

Unit                

 

Serial # 

 

Serial # 

 

Cord 

 

Cord Length: 

 

Cord Length: 

 

Light Kit 

 

Purchased from: 

 

Purchased From 

 

Float 

 

Purchase Date: 

 

Purchase Date:  

 

Control Panel 

 

Summary of Contents for LED3C11














Reviews: