background image

13

 

  

C-25 Timer Control Instructions

Portable Timer with Ground Fault Interrupter

IMPORTANT

This portable timer is designed for CONTROLLING the 

connected equipment only.  Unplug timer before servicing 

the unit or the equipment it controls. For maximum protec-

tion against electrical shock hazard, perform test procedure 

on G.F.C.I. at least once a month.  Mount at least 5 ft. from 

open water.

G.F.C.I. TEST PROCEDURE

The G.F.C.I. should be checked every month to make sure 

that it is operating properly.  Just follow the simple instruc-

tions below.  It is recommended to maintain a maintenance 

diary of your monthly safety check.

 

1.  Push TEST button, RESET button should pop out from 

inner surface.  This should result in power being OFF at 

the outlet protected by the G.F.C.I.  Verify by plugging a 

test lamp into the outlet.  Be sure the timer is in the ON 

position.

 

2.  If the G.F.C.I. tests okay, restore power by pushing the 

RESET button back in.  THE RESET BUTTON MUST BE 

PUSHED FIRMLY AND FULLY INTO PLACE UNTIL IT 

LOCKS AND RE-MAINS DEPRESSED AFTER PRES-

SURE HAS BEEN REMOVED.

 

    

DANGER:  IF RESET BUTTON DOES NOT POP OUT, 

IF TEST LAMP REMAINS LIT WHEN RESET BUTTON 

DOES POP OUT, OR IF THE G.F.C.I. FAILS TO RE-

SET PROPERLY, DO NOT USE TIMER!  CONTACT A 

QUALIFIED SERVICE TECHNICIAN!

Failure to use the C-25 with Kasco Fountains will void the 

warranty and cause the Fountain to not be listed to UL and 

CSA standards via ETL.

UNDER NO CIRCUMSTANCES SHOULD ANYONE 

ENTER THE WATER WHEN A UNIT IS IN OPERA-

TION!

TIMER-OPERATION INSTRUCTIONS

C-25 Control Box will turn the aerator/fountain ON & 

OFF with the TIMER.  Kasco lights will turn ON with the 

PHOTO EYE and OFF with TIMER.  C-25 Control Box is 

to be used with Kasco Approved Lights ONLY!

•  See Control panel label for instructions to set the timer

•  Plug aerator/fountain cord into the RIGHT hand outlet 

(labeled UNIT).

•  Plug transformer light cord into LEFT hand outlet 

(labeled LIGHT).

Summary of Contents for 3400JF

























Reviews: