6
depending on conditions. In most cases a power washer
will be suficient if the unit and algae are still wet. Also
make sure the lens of the light ixtures is clean to ensure the
brightest light possible.
FIXTURE SERVICE: The LED light ixtures are sealed
and do not require any maintenance other than cleaning.
Do not attempt to open light ixtures.
Any required repairs need to be performed by Kasco Ma-
rine. Any alterations or changes made to Kasco units by an
unauthorized source will void the warranty. This includes
tampering with the unit, power cord, and/or control box.
Please contact Kasco Marine, Inc. at 715-262-4488
or [email protected].
Warranty Policy
2 Year Limited Warranty: Kasco® Marine, Inc. warrants
this Light Kit to be free from defects in material or work-
manship under normal use and service. The Kasco Marine,
Inc. obligation under this warranty is limited to replacing
or repairing free of charge any defective part within two (2)
years from the date of shipment. Customer shall pay ship-
ping charges for returning the unit to Kasco.
THIS WARRANTY IS IN LIEU OF ANY OTHER
WARRANTIES, EXPRESSED OR IMPLIED, AND ANY
OTHER OBLIGATION OR LIABILITY WHATEVER
ON THE PART OF KASCO MARINE, INC. AND IN NO
EVENT SHALL KASCO MARINE, INC. BE LIABLE
FOR ANY SPECIAL OR CONSEQUENTIAL DAMAG-
ES.
Warranty is void if:
The Light Kit is not maintained properly according to the
Maintenance Recommendations supplied in this Owner’s
Manual.
The lights, control box, or power cord are altered in any
way from original shipment. Cuts in the power cord are not
covered under warranty.
The Light Kit is damaged by unauthorized tampering.
Warranty Claim Procedure:
The warranty coverage can be established by the date of
purchase receipt or by calling Kasco Marine, Inc. Please
call Kasco Marine at 715-262-4488 prior to shipping to re-
ceive a Return Authorization Number and/or Repair Form,
then ship to:
3. Follow the instruction on the previous page
(LED3S19 Assembly instructions) to mount the light
kit to the brackets.
Maintenance Recommendations
•
DO NOT attempt to open light ixtures!
•
Under No Circumstances should anyone enter the water
while a fountain is operating.
•
Please keep the original box for maintenance shipping.
The following maintenance procedures can be utilized to
ensure many years of quality performance from your Kasco
Fountain and Light Kit and reduce the need for more costly
repair work.
PROPER INSTALLATION: Proper installation of Kasco
equipment will include a power source with ground fault
protection. For Fountain models, Kasco provided control
panels included with the unit have built-in ground fault pro-
tection. Ground fault interrupters are a safety feature that
can also alert you to electrical leaks in the equipment. If
you have repeat, consistent trips of the ground fault device,
the equipment should be disconnected and removed from
the water. The power cord should be inspected for dam-
age and you should contact your distributor, or call Kasco
Marine at 715-262-4488 for further instructions or email
Kasco at [email protected].
OBSERVATION: Operating equipment should be observed
on a regular basis (daily, if possible) for any reduction or
variation in performance. If a change in performance is ob-
served, the equipment should be disconnected from power
and inspected.
WINTER STORAGE: In regions where there is signiicant
freezing in the wintertime, the fountain and light kit should
be removed from the water to protect them from the expan-
sion pressure of the ice. In many areas, fountains will keep
some amount of ice open through the winter. However,
when the water is thrust into the air, it is exposed to the
colder air temperatures longer and can actually make ice
thicker on the pond/lake. Storage over winter is best in a
location that is out of the sun and cool, but above 32° F.
CLEANING: Fountains and light kits should be removed
from the water at least once per year (at the end of the
season in cold climates) to clean the exterior of the sys-
tem, especially the stainless steel motor housing (can) and
light ixtures. The motor housing and light ixture surfaces
dissipate heat into the water and any algae, calcium, etc.
build-up will become an insulator that blocks heat trans-
fer. In warmer regions it is recommended that the motor
is removed and cleaned at least two to three times per year
Summary of Contents for LED3S19
Page 11: ...11 ...
