background image

4

protected outlet and timer.

Instructions for mounting LED3S19 on models:
8400VFX, 800JF, 2.3VFX, 2.3JF, 3.1JF, 3.3JF, 
5.1JF, 5.3JF, 5.1VFX, 5.3VFX, 7.3JF

1. Install the mounting brackets to the light ixtures 

as shown using ¼” lock washers and ¼” x ½” bolts.  
Hand tighten only at this time.

Fig 8

Important Note:  Installation of the LED light ixtures 

on the above listed aerating fountain units with the 
mounting brackets oriented as shown will ensure 

proper submersion of the light ixtures.  Each ixture 

must be partially submerged in order for lights to 

operate properly.  Other applications for these ixtures 

must provide at least the same submersion to properly 

cool the ixture.  Operating the ixtures out of water 

will damage the LED and void warranty.

2. Insert the ¼” x 1” bolt into the light mounting 

bracket.  Align the bracket to the loat bracket by 

placing the bolt through the light mounting hole 

(mounting bracket is on top of the loat bracket) as 

shown in Fig.9

Fig 9

3. Install the ¼” Flat Washer, ¼” Lock Washer and 

5. Install the ¼” Flat Washer, ¼” Lock Washer and 

¼” Nut against the underside of the loat tab as shown 

in Fig. 5.  Tighten the nut until snug using the 7/16” 
wrench.

Fig 5

lat washer

lock washer

1/4” nut

6. Adjust the angle of the light as desired and tighten 
the ¼” x ½” bolts on the sides of the mounting bracket 
until snug.  For more uniform illumination, it is best to 

have all three ixtures at the same angle.

7. Repeat steps 1 through 4 for the remaining ixtures.  

Assembled light ixtures are pictured in Fig. 6.  Note 

the orientation of the lights and mounting brackets.

Fig 6

8. Using the cable ties, tie each ixture cord to bottom 

leg of mounting brackets using the holes provided.  
The will act as a strain relief and will keep the cord 
from being damaged by the fountain and balance the 
unit properly. Next, cable tie the main power cord to 

the loat as shown in Fig. 7.

Fig 7

  

 

9. Upon installation of the assembled unit, connect 

your LED light kit to your ield installed GFCI 

Summary of Contents for LED3S19













Reviews: