Kasco Aeration 3400HJF Owner'S Manual Download Page 2

2

THANKS
We at Kasco Marine, Inc. would like to both thank and 
congratulate you on your purchase of the JF model 
aerating fountain.  We appreciate you choosing Kasco 
and for your purchase.  Your decision to purchase Kas-
co’s JF model Aerating Fountain will not disappoint 
you.  The JF model Aerating Fountain will be a great 
addition to your body of water.  It will help improve 
the water quality by adding much needed oxygen and 
circulation.  It will also enhance the aesthetics of the 
pond or lake with a beautiful fountain pattern.  The 
lighting package (if purchased) will illuminate your 
fountain for beauty at night.  We thank you for choos-
ing Kasco for your fountain needs and want you to be 

completely satisfi ed with your purchase.

Important Safety

Please read and follow these extremely important 
safety and handling instructions for your Kasco equip-
ment.  Following these instructions will help ensure 
your safety and the quality performance of your equip-
ment.

Under NO circumstances should anyone enter the 

• 

water with the electrical equipment plugged in 
and/or in operation.  All Kasco equipment is ETL 
approved to UL and CSA standards for safety in 
water and all fountain models include control pan-
els with GFI protection.  However, it is NEVER 
recommended to enter the water with the equip-
ment in operation.
Caution should be used when dealing with any 

• 

electrical equipment with moving parts.
NEVER run the unit out of water.  It will damage 

• 

the seals and create a dangerous situation for the 
operator.
Extreme caution should be used around water, 

• 

especially cold water, such as in Spring, Fall, and 
Winter, which poses a hazard in and of itself.
NEVER lift or drag the fountain by the power or 

• 

light cord.  If you need to pull the unit to the side 
of the pond, use the anchoring ropes.
Do not use waders in deep ponds/lakes or ponds/

• 

lakes with drop-offs, drastic slopes, or soft bottom 
material.
Do not use boats that tip easily for fountain in-

• 

stallation, such as a canoe, and follow all boating 
safety rules and regulations, including wearing a 

PFD. (Personal Flotation Device)
The fountain is supplied with an internal ground-

• 

ing conductor and a grounding-type attachment 
plug.  To reduce the risk of electrical shock, 
be certain that the fountain is plugged into the 
C-25 Control Box (120V) or C-85 Control Panel 
(240/208V) supplied by Kasco and that the C-25 
is plugged into a properly grounded, grounding 
type receptacle or the C-85 is wired properly.  The 
GFCI breakers should be tested upon each instal-
lation and every month thereafter to ensure proper 

operation.

General Instructions

INSPECT THE SHIPMENT
Immediately inspect your Kasco Fountain shipment 
for any visible damages.  Also cross reference the 
parts supplied with the Parts Included sheet to check 
for shortages.  Shortages should be reported immedi-
ately to your Kasco Marine distributor or representa-
tive and damages reported to your carrier and Kasco 
Marine.

CAUTION
WARNING:  Under NO circumstances should anyone 
enter the water with the unit in operation.  Always 
operate the unit in the water and keep people and ob-
jects clear of the propeller.  Do not lift or pull the unit 
by the electrical cord.  Always use extreme caution 
around electrical equipment and water situations.

ASSEMBLY & INSTALLATION
Please see the proper Assembly and Installation In-
structions enclosed in this manual.  Each is specifi c for 
your model and size of Fountain.  Note:  Use a nylon 
tie to help keep the power cords for the unit and lights 
free of the propeller by tying each cord to either side 
of the fl oat. If you have a light kit, make sure that the 
unit cord is tied to one side of the fl oat and the light 
cord to the other for balance.  Note: It is extremely 
important to test the GFI breaker in the control panel 
upon each installation/reinstallation of the unit to en-
sure proper functioning.

WARRANTY
Kasco Fountains are the result of over 40 years of 
design and engineering.  Kasco products are built to 
withstand the toughest conditions.  Kasco Marine 

Summary of Contents for 3400HJF

























Reviews: