Kasco Aeration 3400HJF Owner'S Manual Download Page 17

17

and determine the year of manufacture according to 
the serial number scheme below:

Sample Serial #
70  01 VX 2  1725
The fi rst two digits represent the reverse of the last 
two digits of the year of manufacture.  
      Example: 80 = 2008 model year.
The third and fourth digits represent the week of the 
year.  (Ex. “01” for 1st week in Jan.) model.  

The best method for establishing warranty period is by 
keeping your original receipt.  Also register the Foun-
tain online at: 
www.kascomarine.com
Kasco Marine will have a record of the purchase and 
will be able to determine whether or not the unit still 
caries warranty coverage.

Once the warranty coverage has been established, the 
unit may be sent to any Kasco Authorized Repair Cen-
ter for evaluation and repair.  Please call Kasco Marine 
at 715-262-4488 prior to shipping.

Kasco Marine, Inc.
800 Deere Rd.
Prescott, WI 54021
Attn: Repairs

Or call Kasco Marine at 715-262-4488 to locate your 
nearest Authorized Repair Center.  You can also email 
Kasco at [email protected]

Note:  Only complete motor assemblies will be ac-
cepted for warranty repair.  The power cord and all 
other components must be returned with the motor 
as originally assembled.  Any missing parts will be 
replaced at the customer’s expense and, if determined 
to have caused the failure, could void the entire war-
ranty.  Some parts are essential for structural support 
during shipping and others, such as the power cord, 
are essential to properly diagnose potential causes of 
failure.  It is not necessary to return the control box or 
fl oat with the motor assembly.

Please include the Repair Form received from Kasco 
Marine or your local distributor with the shipment.  If 
no Repair Form is available, include your name and 
physical address for return delivery of the repaired 
unit and a daytime phone number and/or e-mail ad-

void the warranty.  This includes tampering with the 
unit, power cord, and/or control box.  Please contact 
Kasco Marine, Inc. at 715-262-4488 for your nearest 

Authorized Repair Center.

Warranty Policy

Warranty Period:
Models:  
3400JF, 3400HJF, 4400JF, 4400HJF   - 2 years

Kasco® Marine, Inc. warrants this Fountain to be free 
from defects in material or workmanship (except for 
the ropes, power cord, and propeller) under normal 
use and service.  The Kasco Marine, Inc. obligation 
under this warranty is limited to replacing or repairing 
free of charge any defective part within the warranty 
period from the date of shipment.  Customer shall pay 
shipping charges for returning the unit to Kasco or an 
Authorized Repair Center.

 

THIS WARRANTY IS IN LIEU OF ANY 

OTHER WARRANTIES, EXPRESSED OR IM-
PLIED, AND ANY OTHER OBLIGATION OR LI-
ABILITY WHATEVER ON THE PART OF KASCO 
MARINE, INC. AND IN NO EVENT SHALL KAS-
CO MARINE, INC. BE LIABLE FOR ANY SPE-
CIAL OR CONSEQUENTIAL DAMAGES.

Warranty is void if:

The Fountain is not maintained properly according 

• 

to the Maintenance Recommendations supplied in 
this Owners Manual.
The Fountain is returned for repair without the 

• 

power cord or if the unit, control box, or power 
cord are altered in any way from original ship-
ment.  Cuts in the power cord are not covered 
under warranty.
The Fountain is damaged by unauthorized tamper-

• 

ing.
The Sacrifi cial Zinc Anode around the propeller 

• 

shaft shows signifi cant deterioration.  (The Anode 
must be inspected periodically and replaced if 
necessary.)

Warranty Claim Procedure:
Check the eleven-digit serial number printed either on 
the black cover of the motor or on the blue nameplate 

Summary of Contents for 3400HJF

























Reviews: