background image

9.800-079.0  •  Rev. 4/08

OPERA

T

OR’S MANU

AL

 

PRESSURE 

W

ASHER 

 

8

oPerATING INSTrUCTIoNS

STeP 1: Check engine oil level. Oil level should be level with the bottom 
of the oil filler neck. Be sure the machine is level when checking the oil 
level. (Refer to the engine's operating manual included with machine.) We 
recommend that the oil be changed after the first 5 hours of use, then once 
every 50 hours. Note: Improper oil levels will cause low oil sensor to shut 
off engine.  IMPorTANT! do not run engine with high or low oil levels 
as this will cause engine damage.

STeP  3:  Connect  garden  hose 
to  the  cold  water  source  and  turn 
water on completely. Never use hot 
water.

STeP 5: Rotate the fuel shut-off valve to the "On" po-
sition.  Slide  the  fuel  valve  lever  to  the  "ON"  position.  
When the engine is not in use, leave the fuel valve in 
the "OFF" position.

STeP  4:  Trigger  the  spray  gun  to 
eliminate trapped air then wait for a 
steady flow of water to emerge from 
the spray nozzle.

STeP 2: Fill gas tank with unleaded 
gasoline. Do not use leaded gaso-
line.  Caution: read warnings on 
pg. 4 and engine manual.

STeP 6:  Pull the choke lever out to the "Choke" position 
(on a warm engine, leave the choke lever in, in the run 
position). Push the choke lever to the "Closed" position. 
To restart a warm engine, leave the choke lever in the 
"Open" position.

oil dipstick

Gas  

Tank

Cold 

Water 

Source

Garden 

Hose

Choke 

lever

fuel 

valve

Summary of Contents for SGP-302017























Reviews: