background image

9.800-079.0  •  Rev. 4/08

OPERA

T

OR’S MANU

AL

  

PRESSURE 

W

ASHER 

 

4

 15.  Be  certain  all  quick  coupler  fittings  are  secured 

before using pressure washer.

 

rISk of INjeCTIoN 
or Severe INjUry 

To PerSoNS. keeP 

CleAr of Nozzle.

WArNING

WARNING: High pressure devel-

oped  by  these  machines  will 
cause personal injury or equip-
ment  damage.  Keep  clear  of 
nozzle. Use caution when oper-
ating.  Do  not  direct  discharge 
stream  at  people,  or  severe  in-
jury or death will result. 

 

WArNING

ProTeCT froM 

freezING

WARNING: Protect machine from 

freezing.

16.  To  keep  machine  in  best  
 

operating  conditions,  it  is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

m a c h i n e   f r o m   f r e e z i n g  

 

could cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specified in this manual.

17.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 

WArNING

rISk of 

ASPHyxIATIoN:  USe 

THIS ProdUCT oNly 

IN A Well 

veNTIlATed AreA.

WARNING: Risk of asphyxiation. 

Use  this  product  only  in  a  well 
ventilated area. 

 18.  Avoid  installing  machines  in 

small  areas  or  near  exhaust 
fans.  Adequate  oxygen  is 
needed  for  combustion  or 
dangerous  carbon  monoxide 
will result.

 19.  Manufacturer  will  not  be  liable  for  any  changes 

made to our standard machines or any components 
not purchased from us.

 0.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WArNING

rISk of INjUry 

froM fAllS WHeN 

USING lAdder.

WARNING: Be extremely careful 

when using a ladder, scaffolding 
or any other relatively unstable 
location.  The  cleaning  area 
should  have  adequate  slopes 
and drainage to reduce the pos-
sibility  of  a  fall  due  to  slippery 
surfaces.

 

 1.  Do not allow acids, caustic or abrasive fluids to pass 

through the pump.

 .  Never  run  pump  dry  or  leave  spray  gun  closed 

longer than 1- minutes.

IMPorTANT SAfeTy INforMATIoN

 

  In an overfilling situation, additional precautions are 

necessary to ensure that the situation is handled 
in a safe manner.

WARNING:  Risk  of  injury.  Disconnect  battery 
ground terminal before servicing.

  8.  When in use , do not place machine near flammable 

objects as the engine is hot.

  9.  Oil  burning  appliances  shall  be  installed  only  in 

locations where combustible dusts and flammable 
gases or vapors are not present. Do not store or 
use gasoline near this machine.

 10.  Use No. 1 or No.  heating oil (ASTM D306) only. 

Never use gasoline in your fuel oil tank. Gasoline 
is more combustible than fuel oil and could result 
in a serious explosion. Never use crankcase or 
waste oil in your burner. Fuel unit malfunction could 
result from contamination.

 11.  Do not confuse gasoline and fuel oil tanks. Keep 

proper fuel in proper tank.

WArNING

rISk of INjUry.  

HoT SUrfACeS  

CAN CAUSe bUrNS

WARNING:  Risk  of  injury.  Hot 

surfaces can cause burns. Use 
only designated gripping areas 
of spray gun and wand. Do not 
place hands or feet on non-insu-
lated  areas  of  the  pressure 
washer.

 1.  Transport/Repair with fuel tank EMPTY or with fuel 

shut-off valve OFF. 

 

HoT dISCHArGe flUId:   

do NoT ToUCH or 

dIreCT dISCHArGe 

STreAM AT PerSoNS.

CAUTION:  Hot  discharge  fluid. 
Do not touch or direct discharge 
stream at persons.

WARNING: This  machine  pro-
duces hot water and must have 
insulated components attached 
to protect the operator.

 13.  To  reduce  the  risk  of  injury,  close  supervision  is 

necessary when a machine is used near children. 
Do  not  allow  children  to  operate  the  pressure 
washer. This machine must be attended during 
operation. 

 

TrIGGer GUN kICkS 

bACk - Hold WITH  

boTH HANdS

WArNING

WARNING:  Grip  cleaning  wand 

securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

14.   Never  make  adjustments  on 

machine while in operation.

 

Summary of Contents for SGP-302017























Reviews: