![background image](http://html.mh-extra.com/html/karcher/ps-30-plus/ps-30-plus_manual_655719006.webp)
6
English
Environmental protection
The packing materials can be recycled. Please
dispose of packaging in accordance with the en-
vironmental regulations.
Electrical and electronic devices contain valua-
ble, recyclable materials and often components
such as batteries, rechargeable batteries or oil,
which - if handled or disposed of incorrectly - can
pose a potential danger to human health and the envi-
ronment. However, these components are required for
the correct operation of the device. Devices marked by
this symbol are not allowed to be disposed of together
with the household rubbish.
Working with detergents may only be performed on
watertight surfaces with connection to the waste
water sewage system. Do not allow detergent to enter
waterways or the soil.
Notes on the content materials (REACH)
Current information on content materials can be found
at:
www.kaercher.de/REACH
Intended use
The power scrubber PS 30 Plus can be used with all
Kärcher Home & Garden pressure washers manufac-
tured in 1992 or later, up to a pressure of 18 MPa
(180 bar / 2600 psi).
For devices manufactured up to 1991, an additional
adapter is required (see chapter
).
The power scrubber is ideally suited for high-pressure
cleaning of primarily smooth, outdoor floor areas and
stairs with various different surfaces such as tiles,
stone, concrete, plastic and wood.
Indoor areas such as laundry rooms or garages can al-
so be cleaned as long as they have suitable water drain-
age facilities.
Only use the power scrubber PS 30 Plus in private
households.
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at
www.kaercher.com
.
Description of the unit
For the illustrations, refer to the graphics page
Illustration A
1
Bristle crown
2
Squeegee blade
3
Hinge
4
Union nut
5
Bayonet connector
6
Extension tube
7
Rotary knob for adjusting the side nozzle
8
Rotatable side nozzle
9
Rigid high-pressure nozzle
Mounting the extension tube
Note
Ensure that the device components are tightly connect-
ed on installation.
Illustration B
1. Insert the bayonet connection into the mounting.
2. Turn the extension tube until it engages in place.
3. Tighten the union nut.
Repeat the procedure for further extension tubes if ap-
plicable.
Initial startup
Note
You can use the extension tubes with any KÄRCHER
accessories.
The extension tubes must be installed prior to use (see
chapter
1. Connect the device to the high-pressure gun.
Operation
Cleaning floor areas
Remove coarse dirt from the surface to be cleaned (e.g.
by sweeping) before using the device to avoid damage.
Note
●
Test the device on an inconspicuous area before us-
ing on sensitive surfaces, e. g. wood.
●
Do not allow it to remain in one area, but keep it in
motion.
1. Place the power scrubber onto the surface to be
cleaned.
Illustration C
2. Make sure the side nozzle is directed towards the
floor area. If this is not the case, turn the rotary knob
clockwise to adjust the side nozzle until it is pointing
downwards.
3. Unlock the lever of the high-pressure gun.
4. Press the lever of the high-pressure gun.
The device switches on.
5. Clean the floor area.
6. Wet, smooth surfaces can be dried using the squee-
gee blade.
Illustration D
Cleaning edges and corner areas
The side nozzle and cleaning head can be turned for
convenient cleaning of edges and corner areas.
1. Turn the rotary knob counter-clockwise to adjust the
side nozzle.
Illustration E
The side nozzle is directed to the side.
2. If necessary, turn the cleaning head in the desired
direction.
Illustration F
3. Unlock the lever of the high-pressure gun.
4. Press the lever of the high-pressure gun.
The device switches on.
5. Clean the edges or corner areas using even move-
ments.
After use
Rinse off the device with a gentle water stream after
use.
Remove the power scrubber and extension tubes, if
applicable, from the high-pressure gun.
Rinse off the power scrubber with the high-pressure
gun (without accessories) or wipe down with a damp
cloth.