![background image](http://html1.mh-extra.com/html/karcher/prochem-peak-gtx2/prochem-peak-gtx2_operating-instructions-manual_3879053017.webp)
15
Installation
Lifting Unit Onto Vehicle
Since console weighs approximately 734 lbs. pounds,
we recommend using a forklift to lift unit onto vehicle.
Position forks under unit from front and make CERTAIN
that forks are spread to insert into frame slots.
Positioning Unit In Vehicle
Because vehicles vary in size and openings, individuals
have their own preference as to where they want their
units installed. We strongly recommend a side door
installation for this and
DO NOT
recommend a rear
door installation.
1.
Enough space should be provided to assure
adequate engine ventilation and room for service
and maintenance.
2.
The unit with waste tank and accessories must
NOT
exceed vehicle's axle weight limit. An empty
60 gallon waste tank and console weighs 1014 lbs.
3.
DO NOT
position the console closer than 12" from
bottom of driver and passenger seats.
NOTE: For individuals who wish to make an
engineering layout prior to positioning unit, refer to
"Dimensional Data" illustrations for waste tank and
console dimensions.
Bolting Down Unit And Waste Tank
NOTE: When positioning waste tank with respect to
console, hook up the vacuum hose to waste tank.
This will ensure that waste tank is positioned
correctly. Proceed once unit and waste tank are
positioned in vehicle in desired location.
Before drilling any mounting holes in vehicle floor,
make certain that when drilling, you will not do any
damage to fuel tank, fuel lines, or any vital
component which might affect operation or safety
of vehicle.
Avant de percer les trous de montage dans le
plancher du véhicule, s'assurer que les trous ne
causeront aucun dommage au réservoir à carbu-
rant, aux conduits de carburant ou tout autre
composant essentiel qui pourrait affecter le
fonctionnement ou la sécurité du véhicule.
1.
Using console and waste tank mounting holes as a
template, drill six 13/32" diameter holes for
mounting console and six more 13/32" diameter
holes for mounting waste tank.
2.
Using installation hardware kit:
a. Insert six 3/8-16 x 2" hex head cap screws with
flat washers through mounting holes in console,
and six 3/8-16 x 2" hex head cap screws with flat
washers through mounting holes in waste tank.
b. Install mounting plates underneath vehicle floor.
c. Screw 3/8-16 hex head locknuts on mounting
screws and tighten them until console and waste
tank are firmly secured to vehicle floor.
Electrical Wiring
Ensure all electrical wiring and battery cables are free
from contact with any metal edge. Engine vibration
could cause metal edge to cut wiring and possibly
result in a fire. Be aware of where battery cables are
run.
86411120 Manual Operators - Peak GTX2 Prochem
Summary of Contents for PROCHEM Peak GTX2
