![background image](http://html1.mh-extra.com/html/karcher/km-90-60-r-p/km-90-60-r-p_operating-instructions-manual_654482021.webp)
-
5
Danger
Risk of injury and damage! Do not use a
forklift to unload the appliance.
To unload the machine, proceed as follows:
Cut plastic packing belt and remove foil.
Fill battery with battery acid (see sec-
tion on Care and Maintenance).
Install the battery and connect it (see
section on Care and Maintenance).
Remove the elastic tape fasteners at
the stop points.
Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
Slide the four support beams included
in the packaging under the ramp.
Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.
Slide the machine over the prepared
ramp from the pallet.
The machine can be moved in 2 ways:
(1) By pushing it (see Moving sweeper
without engaging self-propulsion).
(2) By driving it (see Moving sweeper by
engaging self-propulsion).
Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.
Open the device hood.
Set the freewheel lever to OFF.
Note:
If the freewheel lever does not lock
in, then slightly move the machine forward
and backward.
– This blocks the travel drive function.
– Braking effect exists no more.
Close cover.
The machine can now be pushed.
Note:
Do not move the machine for long
distances without engaging self-propul-
sion, a speed of 6 km/h should not be ex-
ceeded.
Set the freewheel lever to ON.
The travel drive is now ready for operation.
Close cover.
The appliance can now be driven.
Note:
The machine has been fitted with an
automatic parking brake that is activated as
soon as the engine is switched off and the
driver leaves his seat.
Park the sweeper on an even surface.
Remove ignition key.
Danger
Risk of explosion!
–
Only use the fuels specified in the Op-
erations Manual.
–
Do not refuel the machine in enclosed
spaces.
–
Smoking and naked flames are strictly
prohibited.
–
Ensure that no fuel reaches the hot
open surfaces.
–
Overflown fuel can form an explosive
misture of fuel and air when it comes in
contact with the blower.
Switch off engine.
Open the device hood.
Open fuel filler cap.
Insert funnel.
Use "regular unleaded petrol".
Fill tank to max. 1 cm below the lower
edge of the filler nozzle.
Wipe off any spilt fuel, remove funnel
and close fuel filler cap.
Close cover.
Note:
The contents of the tank are suffi-
cient to operate the machine for about an
hour.
Check engine oil level.
Check fill level of fuel tank.
Check fill level of hydraulic oil.
Check side brush.
Check roller brush.
Shake off dust filter.
Empty waste container.
Check tyre pressure.
Note:
For description, see section on Care
and maintenance.
Caution
Risk of damage to the axle! Before each
drive, check and ensure that the free-run
lever is at ON position.
Caution
The air inlets next to the driver's seat must
not be covered. Do not store any objects
next to or behind the seat.
Pull seat adjustment lever inwards.
Slide seat, release lever and lock in
place.
Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Note:
The max. load of the storage area is
20 kg.
Fasten the load through appropriate
fasteners at the 4 eyelets.
1 Driving
Driving to the Place of Use.
2 Sweeping with sweep roller
Roller brush is lowered.
3 Sweeping using roller brush and side
brushes
Roller brush and side brushes are low-
ered.
Note:
The machine is equipped with a seat
contact switch If the driver's seat is vacat-
ed, the machine is switched off.
Note:
If the seat contact switch has
switched off the machine, then turn the ig-
nition key to "0" to prevent battery dis-
charge.
Open the device hood.
Before Startup
Unloading
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging self-
propulsion
Start up
General notes
Refuelling
Inspection and maintenance work
Operation
Adjusting driver's seat
Storage area
Programme selection
Starting the machine
Open fuel cock
21
EN