![background image](http://html1.mh-extra.com/html/karcher/hdc-20-8/hdc-20-8_manual_4193479024.webp)
-
8
몇
CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
몇
CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
DANGER
Risk of injury! The main switch is to be
switched off while carrying out any repairs
or maintenance jobs.
Transport
Storage
Care and maintenance
Maintenance schedule
Time
Activity
Assembly affected
Performance
of whom
daily
Check hand-
spray gun
Hand spray gun
Check whether the hand-spray gun closes tightly
without any leaks. Check the protection mecha-
nism against accidental switching. Replace de-
fective hand-spray guns.
Operator
Check high pres-
sure hoses
Outlets, hoses towards working
machine
Check hoses to see if there are damages. Re-
place defect hoses immediately. Danger of acci-
dent!
Operator
weekly or after 40
operating hours
Check the unit for
leaks
Entire plant
Check pumps, overflow valve and pipe system
for leaks. Inform Customer Service if there is oil
below the pump or if there is a leakage of more
than 3 drops of water per minute. Keep the leak-
age borings clear.
Operator/Cus-
tomer service
Check oil level
Oil level indicator on the pump If the oil is milky, it needs to be replaced.
Operator
Check oil level
Oil level indicator on the pump Check oil level of the pump. Refill oil if required
(Order no. 6.288-016)
Operator
monthly or after 200
operating hours
Check pump
High-pressure pump
Check the pump for leaks. If the leakage is more
than 3 drops per minute, call Customer Service.
Operator
Check water
scarcity fuse
Swimmer switch in the swimmer
tank
Press the swimmer of the low water fuse down
for about 5 seconds and control the error indica-
tor on the control board. Remove deposits if nec-
essary.
Operator
Test swimmer
valve
Float tank
The water level must be 40 mm above the over-
flow. No water must exit while the swimmer valve
is closed.
Operator
Check over-
pump time.
Controls
Close consumer loads (e.g. hand spray guns).
The pump must switch off after the afterrun peri-
od.
Operator
Test automatic
start
Pressure sensor
The pump stands still as there is no water trans-
fer. Open the hand spray gun. If the pressure in
the high-pressure cycle falls below the switch-
point, the pump must switch on.
Operator
Tighten hose
clips
All hose clips
Tighten the hose clips using a torque wrench.
Tightening torque up to a diameter of 28 mm =
2Nm, from 29 mm = 6 Nm.
Operator
half-yearly or after
500 operating hours
Oil change
High-pressure pump
Drain off oil. Fill in 1 l of fresh oil (order no. 6.288-
016.0). Check the oil level at the oil level indica-
tor.
Operator
half-yearly or after
1000 operating
hours
Check the appli-
ance for calcium
deposits
entire water system
Improper functioning of valves or pumps can be
an indication of calcium deposits. If necessary
decalcify.
Operator
trained in de-
calcification
Tighten clamps Control board
Tighten all clamps for components in the main
circuit.
Electrician
Test swimmer
valve
Float tank
The water level must be 40 mm above the over-
flow. No water must exit while the swimmer valve
is closed.
Customer
Service
annual
Safety check
Entire plant
Safety check according to the guidelines for fluid
spraying equipment.
Technical ex-
pert
24
EN