Kärcher ARMADA BRC 40/22 C Manual Download Page 29 | Manualshive

Page: 29 / 61

background image

29

Tower removal process

Removal of the tower allows access to the solution tank cover/gasket, the strainer assembly and outlet hose from the tank to the
strainer. The Steering shaft removal process needs to be performed in order to remove the tower assembly (see instructions on
pages 23-28.

Using the T-20 Torx driver remove the 5 screws towards
the front of the tower.

Lay the machine on it’s side and remove the 10
screws from the bottom of the tank.

Remove the 4 screws holding the axel/
wheel assembly.

Remove the screws from the wheel wells (2 on each side).

«
...
27
28
29
30
31
...
»

Summary of Contents for ARMADA BRC 40/22 C






























































Reviews:

No comments

Related manuals for ARMADA BRC 40/22 C

Brand: Daewoo Pages: 31

Brand: Daewoo Pages: 4

Brand: DAEWOO ELECTRONICS Pages: 30

Brand: Orava Pages: 22

NT 561 Eco Package Craftsmen

Brand: Kärcher Pages: 23

Brand: Tapo Pages: 24

Brand: PUR Pages: 10

Brand: Fein Pages: 361

Brand: Zepter Pages: 22

Brand: Ghibli Pages: 19

Brand: Rac Pages: 3

DEEBOT OZMO 610

Brand: ECOVACS ROBOTICS Pages: 6

Brand: Zelmer Pages: 40

MINI SPACE RO18234A

Brand: Rowenta Pages: 29

Brand: Exido Pages: 16

Brand: Dyson Pages: 12

Brand: Dyson Pages: 16

Brand: Dyson Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands