Kärcher ARMADA BRC 40/22 C Manual Download | Manualshive

Page: 26 / 61

background image

26

Lift the rubber seal off of the deck pivot and work it up the wire harness to expose the snap ring. On machines
built with the waterproof harness this seal is not present.

Using a pair of snap-ring pliers, remove the snap-ring
separating the pivot from the mount.

There is a ball bearing in the trough of the pivot, it is
the steering stop, remove it and place it where it won’t
get lost.

«
...
24
25
26
27
28
...
»

Summary of Contents for ARMADA BRC 40/22 C






























































Reviews:

No comments

Related manuals for ARMADA BRC 40/22 C

Brand: AiroDoctor Pages: 8

Shark Navigator Lift-AWAY H-8831

Brand: U-Line Pages: 21

Sanitaire H-2536

Brand: U-Line Pages: 6

Brand: U-Line Pages: 3

Rocket Powerhead AH450UK

Brand: Shark Pages: 12

EPFX HEPA375VSC

Brand: EnviroPureFX Pages: 4

Brand: Hanseatic Pages: 72

Brand: Goblin Pages: 16

Deck `N Drive IN464900AV

Brand: Campbell Hausfeld Pages: 12

Brand: Shark Pages: 20

Brand: UFESA Pages: 36

Brand: Prem-I-Air Pages: 8

Brand: Airgle Pages: 5

Brand: Domo Pages: 23

Sai HydroPur AVC-2001

Brand: Aroma Pages: 16

Brand: Kaysun Pages: 20

PrecisionPro EL8850 Series

Brand: Electrolux Pages: 9

Pronto all floors

Brand: Electrolux Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands