background image

9.800-191.0  •  Rev. 01/18

OPERATOR’S MANUAL  

 PRESSURE 

WASHER  

4

IMPORTANT SAFETY INFORMATION

 10.  Keep operating area clear of all persons.

WARNING

USE PROTECTIVE  

EYE WEAR 

AND CLOTHING  

WHEN OPERATING 

THIS EQUIPMENT.

WARNING: High pressure spray 
can cause paint chips or other 
particles to become airborne 

and fly at high speeds. To avoid 

personal injury, eye, hand and 
foot safety devices must be 
worn.

 11.   Eye, hand, and foot protection 

must be worn when using this 
equipment.

WARNING

EAR PROTECTION 

MUST BE WORN

WARNING: This machine exceeds 
85 db appropriate ear protection 
must be worn.

 

WARNING

HOT DISCHARGE FLUID: 

DO NOT TOUCH OR 

DIRECT DISCHARGE 

STREAM AT PERSONS.

WARNING: Hot discharge fluid. 

Do not touch or direct discharge 
stream at persons.
WARNING: This machine pro-
duces hot water and must have 
insulated components attached 
to protect the operator.

WARNING

RISK OF INJURY:  

HOT SURFACES  

CAN CAUSE BURNS

WARNING: Risk of injury. Hot 
surfaces can cause burns. Use 
only designated gripping areas 
of spray gun and wand. Do not 
place hands or feet on non-insu-
lated areas of the pressure 
washer. 

12.  To reduce the risk of injury, 

 

close supervision is necessary 

 

when a machine is used near children. Do not al-
low children to operate the pressure washer. 

This 

machine must be attended during operation. 

 

TRIGGER GUN KICKS 

BACK - HOLD WITH  

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 
securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

13.   Never  make  adjustments  on 

machine while in operation. 

 14.  Be certain all quick coupler fit-

tings are secured before using 
pressure washer.

RISK OF INJECTION 

OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-
oped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people, or severe in-
jury or death will result. 

 

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 
freezing.

15.  To keep machine in best  
 

operating conditions, it is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

m a c h i n e   f r o m   f r e e z i n g  

 

could cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol

-

low storage instructions specified in this manual.

16.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 

WARNING

RISK OF 

ASPHYXIATION: USE 

THIS PRODUCT ONLY 

IN A WELL 

VENTILATED AREA.

WARNING: Risk of asphyxiation. 

Use this product only in a well 

ventilated area. 

 17.  Avoid  installing  machines  in 

small areas or near exhaust 
fans. Adequate oxygen is 
needed for combustion or 
dangerous carbon monoxide 
will result.

 18. Manufacturer will not be liable for any changes 

made to our standard machines or any components 
not purchased from us.

 19.  The best insurance against an accident is precau-

tion and knowledge of the machine.

WARNING

RISK OF INJURY FROM 

FALLS WHEN USING 

LADDER.

WARNING: Be extremely careful 
when using a ladder, scaffolding 
or any other relatively unstable 
location. The cleaning area 
should have adequate slopes 
and drainage to reduce the pos-
sibility of a fall due to slippery 
surfaces.

 

 20.  Do  not  overreach  or  stand  on  unstable  support. 

Keep good footing and balance at all times.

 21.  Do not operate this machine when fatigued or under 

the influence of alcohol, prescription medications,  
or drugs.

New & Reconditioned Equipment & Parts - www.southeasternequipment.net

Summary of Contents for 1.575-511.0

































Reviews: