KAP Medical K-3 ELITE Operating Instructions Manual Download Page 29

Page: 29 / 38

K-3 & K-4 Series Owner’s Manual

Page 28

CLEANING PROCEDURE

WARNING:

Before attempting to clean the control unit, turn off and disconnect the power cord from the power

source.

WARNING: DO NOT HEAT, STEAM AUTOCLAVE, OR IMMERSE THE CONTROL UNIT IN LIQUIDS

Control Unit:

Wear eye goggles and protective gloves before starting the cleaning procedure.

The following germicidal detergents / disinfectants are recommended by the EPA as hospital disinfectants.

a. Johnson Wax, Virex 128, EPA Registration Number 47371-130-4822.

b. Quaternary Detergent-Disinfectant by

Airkem Professional Products, Division of
Ecolab, Inc., Ecolab Center, St. Paul,
Minnesota.  EPA registration number: EPA
# 42964-5.

c. Hi-Tor Germicidal Detergent by Huntington

Laboratories, Inc. Huntington, Indiana.
EPA registration number: EPA # 303-91.

Note: A spray bottle of fresh disinfectant / detergent solution should be prepared daily to clean the
control unit.

Prepare the required amount of solution by following the preparation instructions provided with the germicidal

detergent /disinfectant solution.

Pour required amount into a spray bottle.

Use a brush or cloth to wipe off dust. If necessary, spray the exterior of the top and the bottom enclosures, power

cord and the cord plug with the prepared disinfectant / detergent solution. Using a damp cloth, wipe down the
sprayed surface cleanly.

Note: Do not spray excess amount of solution on the control unit.

6. Once the control unit is clean, wipe the unit, power cord, cord receptacle, and the cord plug with a clean dry cloth.

7. Place the control unit to dry in a cool, dry area for an hour before operating or storing the unit. If the control unit is

not used immediately, place the control unit in a plastic bag and store it in a storage area.

8. After the cleaning operations are completed, remove and dispose the protective gloves appropriately. Wash your

hands thoroughly with antibacterial soap.

Air Mattress

WARNING:

To prevent damage, please remove the Auto Fowler sensor (if present) from the base of the

mattress before laundering. The Auto Fowler sensor is located in a small pocket inside the base

of the mattress located on the patient’s right hand side, 12-15 inches from the head end of the
mattress.

1. Wear eye goggles and protective gloves before starting the cleaning procedure.

2. Follow steps 2 through 4 above to prepare disinfectant solution.

Summary of Contents for K-3 ELITE







































Search results

Summary of Contents for K-3 ELITE

Reviews:

Related manuals for K-3 ELITE

Brands by name

Popular brands

KAP Medical K-3 ELITE, Operating Instructions Manual

Search results

Summary of Contents for K-3 ELITE

Reviews:

Related manuals for K-3 ELITE

Brands by name

Popular brands