background image

 

 

                                        

User Manual 

BW3-070/4

 

 

 

Page 18 of 28 

 

Kanmed Baby Nest 

The Baby Nest is a consumable. The Kanmed Baby Nest must be changed as soon as it shows signs of 
damage or wear, or at least after one year of use.

 

Disposable Nests (single patient type) are also available, please contact your local distributor or visit 

www.kanmed.se

 for more information. 

Periodical Checks 

Recommended checks

 

To be done by

 

Interval

 

Water level in the Water Mattress, Heating Pad, 
Baby Nest - are they clean and undamaged? 
Check the Water Mattress daily for leaks 

The user 

Every time the bed is 
made 

Cables and connectors - clean and undamaged? 

The user 

At each start 

Correct self test at start 

The user 

At each start 

Check of safety systems as per chapter 9 

Technician or user 

Every year 

Electronics safety test (as per hospital routine) 

Technician 

Every year 

Temperature check as below 

Technician or user 

Every year or when in 
doubt 

Temperature Check 

To perform the temperature check a precision thermometer preferably with a skin type sensor is needed. 
The built in temperature monitor with an YSI400 type sensor (having an specified accuracy better than 
±0,2°C) may be used.  

Note

In this procedure the standard type Kanmed Water Mattress must be used. 

 

Make up the bed as for normal use and place the temperature sensor in the centre 

on top of

and 

fixed in direct contact with the Water Mattress (e.g. using a surgical tape or similar). Cover the sensor 
with some insulating material. Check that there is no air in the Water Mattress. 

 

Set the temperature to 37

 O

C and allow the system to settle temperature in steady state (note, this 

may take several hours). 

 

Check that the precision thermometer (or the built in temperature monitor) and the Control Unit 
displays the same reading, allowed difference ± 0.7

O

C. 

 

 

8   Alarm functions, indication and actions 

Temperature monitor alerts 

These alerts relates to the built in temperature monitor, and does not effect the function of the 
BabyWarmer. The temperature monitor is only activated when an YSI400 compatible temperature sensor 
is connected. If a temperature monitor alarm condition is detected, the alarm is activated, indicated on the 
display by a flashing thermometer icon, audio signal and the yellow LED. After pressing the alarm button, 
the alarm will be silenced for 2 minutes. If the alarm condition remains, the alarm will return. 
 

Indication 

Description / Operator action 

 

(FLASHING) 

 
High temperature.

 The measured sensor temperature is higher than the 

set high alarm limit  

 

Action

:

 Check the settings and the patient's actual body temperature. 

Remember that the Water Mattress cools slowly. 

 

Temperature OK!

 (Normally displayed). The measured sensor 

temperature is in between the High- and Low alarm limits. 

 

(FLASHING) 

Low temperature. 

The measured sensor temperature is lower than the 

set low alarm limit.  

Action

:

 Check that the temperature sensor is properly applied to the 

patient. Check that the BabyWarmer system is working in a correct way, 
and that right temperature settings are used. If the sensor temperature is 
rising, but not yet reached up to the Low alarm level, the indicator 
indicates blue but not flashing (no alarm condition!). 

Summary of Contents for BABYWARMER BW3





























Reviews: