12
OODMANUAL 0720
KAM CONTROLS, INC.
I N S TA L L AT I O N C O N T I N U E D
ANALYZER LOOP INSTALLATION
KAM CONTROLS recommends this installation for 3/4" and 1" MNPT OOD™ sensors.
We recommend using thread sealant and not Teflon tape for the OOD™ sensor threads.
CAUTION: DO NOT USE THE ENCLOSURE TO TIGHTEN OR LOOSEN THE OOD. THIS CAN CAUSE THE PROBE TO
COME UNDONE AND THE FIBER CABLE TO BREAK. Please refer to “Installation Do’s and Don’ts” on pages 5-6.
KAM 3/4" and 1" MNPT OOD™ sensors should be
installed according to FIG. 3-14. The OOD™ sensor
should be installed in an analyzer loop in such a
fashion that the flow sweeps across the probe lens
rather than rushing directly at the probe.
If the OOD™ is installed with the product rushing
directly at the probe, particles in the pipeline can
scratch the lens causing abrasions and resulting in a
non-credible reading.
You do not need to measure for insertion distance
on fast loop models.
FLANGED FIXED INSERTION MODELS
INSTALLATION
On flanged fixed insertion models, the insertion
distance has been calculated at the factory based
on supplied end user measurements. These
measurements should be double checked against
the actual site measurements at the time of
installation. These can be installed either on a "T" or
on a main line with a diameter of greater than 4".
FIG. 3-15 and FIG. 3-16.
P
Flow
Flow
Pump
FIG. 3-14
A
A
1
1
2
2
A
A
B
B
MATERIAL
FINISH
DRN
THIS DRAWING IN DESIGN AND
DETAIL IS THE PROPERTY OF
KAM CONTROLS INCORPORATED.
IT SHALL NOT BE REPRODUCED
AND SHALL BE RETURNED TO US
ON DEMAND
ALL RIGHTS RESERVED
APPVD
SCALE
DATE
DWG NO.
REV
TITLE
UNLESS OTHERWISE
SPECIFIED
ALL DIM IN INCHES
ANGULAR TOL ±1/2
FRACTIONAL TOL ±1/64
3 PLACE DEC ±0.005
2 PLACE DEC ±0.010
REMOVE ALL BURRS
BREAK SHARP EDGES
DO NOT SCALE DWG
SHEET
N/A
Gerry Alejos
6/30/2020
A
OID/OOD Fix Insertion
recommended installation
for 2",3" and 4"pipe sizes
134-021-040-000
3939 Ann Arbor Dr.
Houston TX 77063
USA
WWW.KAM.COM
1
OF
1
A
K m
a
SECTION A-A
SCALE 1:8
A
A
1
1
2
2
A
A
B
B
MATERIAL
FINISH
DRN
THIS DRAWING IN DESIGN AND
DETAIL IS THE PROPERTY OF
KAM CONTROLS INCORPORATED.
IT SHALL NOT BE REPRODUCED
AND SHALL BE RETURNED TO US
ON DEMAND
ALL RIGHTS RESERVED
APPVD
SCALE
DATE
DWG NO.
REV
TITLE
UNLESS OTHERWISE
SPECIFIED
ALL DIM IN INCHES
ANGULAR TOL ±1/2
FRACTIONAL TOL ±1/64
3 PLACE DEC ±0.005
2 PLACE DEC ±0.010
REMOVE ALL BURRS
BREAK SHARP EDGES
DO NOT SCALE DWG
SHEET
N/A
Gerry Alejos
1:8
6/30/2020
A
OID/OOD Fix Insertion
Typical installation for 4"
pipes and larger
134-061-040-000
3939 Ann Arbor Dr.
Houston TX 77063
USA
WWW.KAM.COM
1
OF 1
A
K m
a
REVISION HISTORY
REV
DESCRIPTION
DATE
A
New Drawing
6/30/2020
FIG. 3-15
FIG. 3-16
