manualshive.com logo in svg

Kalkhoff Derby Cycle Werke GmbH 2011, User Manual

The Kalkhoff Derby Cycle Werke GmbH 2011 is a high-quality and reliable bike that offers outstanding performance and durability. To fully enjoy the features and functions of this exceptional product, make sure to download the user manual for free from our website manualshive.com.

Share
Download
background image

II User Manual Fast Pedelec 

 

  27

12.3   Components that do not require a 

certificate of approval

 

•

Cranks

 

•

Pedals:  
providing type-approved pedal reflectors are 
used.

 

•

Mudguard:  
the front edge of the front mudguard must be 
rounded.

 

•

Pannier rack

 

•

Saddle

 

•

Handlebar grip

 

•

Gear-shift components:  
Only if the largest gear ratio is not modified.

 

•

Seatpost

 

•

Bell:  
Can be replaced with an equivalent bright-
sounding bell.

 

•

Rear-view mirror:  
Can be replaced with a different type-ap-
proved rear-view mirror.

 

•

Chain

 

•

Headset

 

•

Inner tube

 

•

Hubs

Summary of Contents for Derby Cycle Werke GmbH 2011

































































































































































































































































































































































































Reviews:

No comments

Related manuals for Derby Cycle Werke GmbH 2011

NAKTO Discovery Assembly Instructions Manual preview
Discovery
Brand: NAKTO Pages: 26
devinci TROY 8402 Technical Manual preview
TROY 8402
Brand: devinci Pages: 25
Surly Dummy Deck Instructions preview
Dummy Deck
Brand: Surly Pages: 4
Abus Bordo 6500A Operating Instructions Manual preview
Bordo 6500A
Brand: Abus Pages: 75
Kayoba E-legance 2022 Operating Instructions Manual preview
E-legance 2022
Brand: Kayoba Pages: 63
Argos 836/5967 Maintenance Manual preview
836/5967
Brand: Argos Pages: 12
Öhlins DH38 Workshop Manual preview
DH38
Brand: Öhlins Pages: 27
Gazelle 653540100 User Manual preview
653540100
Brand: Gazelle Pages: 20
Liberty Electric Bikes EB-629 Swan User Manual preview
EB-629 Swan
Brand: Liberty Electric Bikes Pages: 14
Liberty 123 24v FoldNGo User Manual preview
24v FoldNGo
Brand: Liberty 123 Pages: 17
Geuther 2970 Quick Start Manual preview
2970
Brand: Geuther Pages: 8
Babboe HWWX-840 Instruction Manual preview
HWWX-840
Brand: Babboe Pages: 20
E-Broh PASION User Manual preview
PASION
Brand: E-Broh Pages: 16
AmericanElectric STELLER Manual preview
STELLER
Brand: AmericanElectric Pages: 35
Kriega OS-32 Fitting Instructions preview
OS-32
Brand: Kriega Pages: 4
Crivit 307553 Operation And Safety Notes preview
307553
Brand: Crivit Pages: 279
O2Feel Peps Fold Up User Manual preview
Peps Fold Up
Brand: O2Feel Pages: 94
Light motion Urban 180 Instruction Manual preview
Urban 180
Brand: Light motion Pages: 10

Brands by name

Popular brands

Load more brands