manualshive.com logo in svg

Kaiser Willys Tigertop 51405, Installation Instructions Manual

Share
Download
Kaiser Willys Tigertop 51405 Installation Instructions Manual Download Page 9

Tigertop™ – Installation Instructions

Secure Door Flaps

Secure Front of Side Curtain

W

around the Horizontal Rod and fasten the hook and 

loop strips to each other. 

W

around the Vertical Rod (not the front bow) and 

fasten the hook and loop strips to each other.

Wrap Flap around 

Horizontal Retainer

Front

Hook and Loop 

Fastener

Front Bow

Front

Vertical Rod

View from inside vehicle 

- Driver's Side

Locate the snap on each front corner of the top, 

above the windshield. Pull the fabric forward and 

down to eliminate wrinkles and mark the locations 

of the Body Studs. Center punch and drill a 3/32" 

hole at each location. Install a Body Stud with a #6 

x 3/8" Sheet Metal Screw.

Install Front Corner Snaps

For best possible installation, check to 

make sure that the soft top is perfectly 

centered on the vehicle.

View from front

Install Body 

Studs

Install Body Studs

Windshield

Driver's Side of Vehicle

Make sure space between top 

equal on both sides 

Summary of Contents for Tigertop 51405














Reviews:

No comments

Brands by name

Popular brands

Load more brands