Kaba 7102 series Installation Instructions Manual Download Page 22

Page: 22 / 24

L. TROUBLESHOOTING

Lock fails to open when combination is entered and outside thumbturn is

rotated clockwise.

Buttons were not fully depressed when the combination was entered.

Lock not cleared of previous attempts to enter access codes.

Turn the outside thumbturn to the left to clear the wrong entry. Enter the

combination making sure you feel each button click to know that

it was depressed fully. Turn thumbturn clockwise.

Turning outside thumbturn clockwise always retracts latch without

depressing any buttons.

Lock is in zero combination.

Follow the procedure for setting a new combination (Section J, but omit

Step J-2).

Inside thumbturn only retracts bolt partially or not at all, in either clock-

wise or counterclockwise direction.

Bolt was not properly installed.

Remove and re-install the bolt. Review and follow instructions in Section E.

After setting a new combination, the lock works one time only, then fails to

open.

Buttons of intended combination were not fully depressed when changing

combination.

This is a lost combination situation. Review and follow instructions in

Section K.

For technical assistance please call

1-800-849-TECH (8324) or 336-725-1331

Summary of Contents for 7102 series

























Search results

Summary of Contents for 7102 series

Reviews:

Related manuals for 7102 series

Brands by name

Popular brands

Kaba 7102 series, Installation Instructions Manual

Search results

Summary of Contents for 7102 series

Reviews:

Related manuals for 7102 series

Brands by name

Popular brands