background image

7

PRELIMINARY

K-CTRL

5. WARRANTY

6. GENERAL WARNINGS

K-array  systems    are  warranted  against  manufacturing  defects  in  materials  or 
craftsmanship as determined by the distributor. During the warranty period K-array will, 
at it’s discretion, either repair or replace products which prove to be defective provided 
that the product is returned in its original packaging, shipping prepaid, to an authorized 
K-array service agent or distributor. K-array cannot be held responsible for defects caused 
by unauthorized modifications, improper use, negligence, exposure to inclement weather 
conditions, act of God or accident, or any use of this product that is not in accordance with 
the instructions provided by K-array. K-array is not liable for consequential damages. This 
warranty is exclusive and no other warranty is expressed or implied. This warranty does 
not affect your statutory rights.

7. SAFETY INSTRUCTION

•  Do not connect the AC power plug to the 

unit before assembly has been completed.

•  Only  connect  this  unit  to  a  mains  socket 

outlet  with  protective  earth  connection, 
ground-fault  (earth-fault)  protection  and 
overload protection.

•  Do not install the power supply  in wet or 

humid  locations  without  using  weather 
protection.

•  Do not allow water or any foreign object to 

get  inside  the  device.  Do  not  put  objects 
containing liquid on, or near, the unit.

•  To  reduce  the  risk  of  overheating  the 

device, avoid exposing it to direct sunlight. 
Do  not  install  the  unit  near  heat  emitting 
appliances, such as a room heater or stove.

•  No  naked  flame  sources  such  as  lighted 

candles should be placed on the device.

•  To pull the AC Cord out of the wall outlet or 

the unit’s AC socket, never pull the cable 
itself, but only the AC plug.

•  Disconnect  the  unit  from  AC  supply  by 

pulling  the AC  plug  out  of  the  wall  outlet 
or  the  unit’s  AC  socket  before  any  kind 

•  Read this manual completely before using 

the product.

•  Keep this manual in your records for future 

reference.

•  Take  care  of  enough  distance  between 

this product and sources of hum and noise 
like electric motors and transformers.

•  Carry this product with greatest care. Being 

dropped  or  subjected  to  heavy  vibration 
may damage this product mechanically.

•  The  manufacturer  takes  no  responsibility 

for  injury  or  damage  caused  by  not 
following  the  safety  precautions  and 
instructions printed in this manual.

•  Follow  all  printed  security  advice  on  the 

product  itself.  The  lightning  flash  with 
arrowhead  within  an  equilateral  triangle 
makes  you  aware  of  non-insulated 
AC  mains  voltage  inside  the  unit.  The 
exclamation  mark  within  an  equilateral 
triangle  makes  you  aware  of  important 
operating and maintenance instructions in 
the literature attached to this product.

 

Summary of Contents for K-CTRL





















Reviews: