JVC MX-J170V Service Manual Download Page 20

Page: 20 / 78

MX-J170V

1-20

Fig.5

Drive belt

Motor

terminal

Motor

FR belt

Washer

Capstan

washer

Flywheel

Capstan

washer

Mecha.

board

Fig.6

Fig.7

Fig.8

Fig.9

Sleeve

Removing the motor.

1. Remove the two screws D fixing the motor.
Be careful to grease's splash when the

drive belt comes off.(Fig.5, Fig.6)

2. Unsolder the motor terminal.(Fig.5)

Removing the mechanism board.

1. Unsolder the four parts a on the solenoid
coil terminal.(Fig.5)

2. Remove the two screws E fixing the board.(Fig.5)

3. Unhook the three parts b from the board.(Fig.5)

4. Remove the mechanism board.(Fig.5)

Removing the flywheel.

Remove the cut-washers at c and d from the
capstan shaft, then remove the flywheel.
When reassembling the flywheel,
be sure to use new washers as they
cannot be reused.(Fig.8, Fig.9)

Summary of Contents for MX-J170V















































































Search results

Summary of Contents for MX-J170V

Reviews:

Related manuals for MX-J170V

Brands by name

Popular brands

JVC MX-J170V, Service Manual

Search results

Summary of Contents for MX-J170V

Reviews:

Related manuals for MX-J170V

Brands by name

Popular brands