JVC MX-J170V Service Manual Download Page 16 | Manualshive

Page: 16 / 78

background image

MX-J170V

1-16

Prior to performing the following procedure, remove
the CD tray.

Detach the belt from the pulley on the upper side of
the CD changer unit (Do not stain the belt with
grease).

Disconnect the card wire from the pickup unit
connector on the under side of the CD changer unit.

Disconnect the motor wire harness from connector
on the CD mechanism board.

Remove the two screws Y attaching the CD servo
board. First release the n side of the two tabs n and
two tabs o attaching the CD servo board motor to
raise the CD servo board slightly, then release the o
side.

If the tabs n and o are hard to release, it is
recommendable to unsolder the two soldered parts
on the motor terminal of the CD servo board.
Disconnect the terminal CW3 connected to the
switch board and remove the CD servo board.

Remove the screw Z attaching the CD Changer unit
and release the three tabs p attaching the switch
board outward and detach the switch board.

1.

2.

3.

4.

5.

Removing the belt, the CD servo board
and the switch board (See Fig.40 and 41)

Z

Fig.41

Fig.40

Belt

CD changer unit

Y

CD servo board

Tabs o

Tabs n

Soldered parts

Motor

Switch board

CW3

Tabs p

CD mechanism board

motor connecter

Pickup unit connector

«
...
14
15
16
17
18
...
»

Summary of Contents for MX-J170V















































































Reviews:

No comments

Related manuals for MX-J170V

Brand: Eaton Pages: 32

Brand: Zenith Pages: 14

Brand: C SEED Pages: 32

Brand: M-LOCKS Pages: 3

Brand: dB Technologies Pages: 4

Brand: dB Technologies Pages: 89

Brand: dbx Pages: 51

Brand: dBTechnologies Pages: 4

Brand: ICMA Pages: 2

Brand: Fender Pages: 56

Brand: FBII Pages: 48

Brand: Gateway Pages: 8

Brand: Gateway Pages: 116

Brand: LAON TECHNOLOGY Pages: 58

Brand: RainSoft Pages: 16

Brand: Samsung Pages: 42

Brand: LaserLine Pages: 68

Brand: CAME BPT Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands