JVC MX-J170V Service Manual Download Page 12

Page: 12 / 78

MX-J170V

1-12

Prior to performing the following procedure, remove
the top cover and the side covers.

Remove the two screws O attaching the heat sink
plate.

Remove the two screws P attaching the power IC to
the heat sink and the two screws Q attaching the
heat sink to the VCD Power board.

Removing the heat sink & VCD Power
board (See Fig.24 and 25)

Prior to performing the following procedure, remove
the VCD Power board.

Disconnect the power cord from connector RCW2 of
the power transformer.

Disconnect the harness from connector RCW1 of the
power transformer.

Remove the four screws R attaching the power
transformer.

Removing the power transformer

(See Fig.26)

Prior to disconnecting the power cord
from the body, remove the rear panel.

ATTENTION:

Fig.26

Fig.25

Fig.24

VCD Power board

Power cord

RCW2

RCW1

Power transformer

Heat sink

VCD Power board

Summary of Contents for MX-J170V















































































Search results

Summary of Contents for MX-J170V

Reviews:

Related manuals for MX-J170V

Brands by name

Popular brands

JVC MX-J170V, Service Manual

Search results

Summary of Contents for MX-J170V

Reviews:

Related manuals for MX-J170V

Brands by name

Popular brands