JVC MX-J170V Service Manual Download Page 9 | Manualshive

Page: 9 / 78

background image

MX-J170V

1-9

Prior to performing the following procedure, remove
the top cover, the side covers, the CD Tray fitting
and the CD changer unit.

There is no need to remove the rear panel.

Disconnect the harness from head wire connector
ECW1,DW1 and DW2 on the inner side of the main
board in the body.

Disconnect the harness from connector HCW1 of the
headphone board on the right side of the body.

Remove the three screws D attaching the front panel
assembly on both sides of the body.
Remove the screw E attaching the earth terminal
extending from the front compartment.

Remove the screw F attaching the front panel
assembly on the bottom of the body.

Release the two joints d on both sides and two joints
e on the bottom of the body using a screwdriver. At
the same time, disconnect the front compartment
from connector CCW1 and CCW2 of the main board.

1.

2.

3.

4.

5.

Removing the front panel assembly

(See Fig.14 to 16)

Fig.14

Fig.15

Fig.16

Main board

DW2

DW1

CCW1

CCW2

Front panel assembly

Joint d

earth wire

D

E

Front panel assembly

D

D

Main board

MIC
/Headphone board
HCW1

F

Joint e

Joint e

Joint d

ECW1

«
...
7
8
9
10
11
...
»

Summary of Contents for MX-J170V















































































Reviews:

No comments

Related manuals for MX-J170V

security system

Brand: Safe-at-home Pages: 5

Concord express

Brand: GE Pages: 3

Concord express

Brand: GE Pages: 32

Brand: Abicor Binzel Pages: 42

Brand: M-E Pages: 20

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 12

Brand: WaterLogic Pages: 29

EcoTouch Ai1 Geo

Brand: WATERKOTTE Pages: 60

Soundmaster 138

Brand: SOUNDMASTER Pages: 1

Brand: Monacor Pages: 3

OBERON C Series

Brand: Dali Pages: 19

Brand: DAPAudio Pages: 20

Olympica Center

Brand: Sonus Faber Pages: 23

Brand: TDK Pages: 13

Brand: M&S Systems Pages: 2

Brand: Harman Pages: 11

Brand: ATC Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands