14
2. CONTROLS, INDICATORS AND CONNECTORS
STATUS
SHUTTER
MENU
FILTER
3200k
1
5600k+1/8ND
2
5600k+1/64ND
3
ALARM
MONITOR
OPERATE
NG
GAIN
OUTPUT WHT.BAL
VTR
ON
OFF
AUTO IRIS
LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
LIGHT
ON
OFF
COUNTER
AUDIO SELECT
MANUAL
AUTO
CH-1
CH-2
CH-1
CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
CH-1
MIX
CH-2
RESET
OPERATE/WARNING
MONITOR
SELECT
CH-1 AUDIO
LEVEL
CH-2
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFF
RM
DC IN
/BATT.
CALL
CARBON
DYNAMIC
FULL AUTO
BLACK
AUDIO SELECT
CONTINUE
MANUAL
AUTO
INT
EXT
AUX
GROUP
ITEM
SELECT
DATA SET
HOLD
SHIFT
ADVANCE PRESET
CAM
CH-1
CH-2
CH-1
CH-2
REAR
FRONT
AUDIO INPUT
CH-1
SEE
INSTR-
UCTION
MANUAL
CH-2
AUDIO
LEVEL
VTR SELECT
VTR INPUT
PARA
REC
FREE
PRST
REGEN
TC GENE.
MENU
LITHIUM BATT.
A
B
9
H
C D
5
6
E
F
7
8
G
0
3
1 2
[Audio setting]
1
Monitoring loudspeaker
• Enables EE monitoring of the input audio signal during
recording, in the record-pause mode or in the stop mode.
Outputs the playback sound in the playback mode.
The sound to be output can be selected using the
MONITOR SELECT switch
4
.
• The loudspeaker volume can be adjusted with the
MONITOR volume control
2
on page 12.
The audio from the loudspeaker is not output when an
earphone is plugged into the EARPHONE jack
2
on page
22. The warning alarm tones are also output through this
loudspeaker.
☞
See “ALARM INDICATIONS” on pages 96.
2
[CH1 AUDIO LEVEL] CH1 audio input level control
Adjust the audio input level of the CH1 audio channel with
this control.
• To use this control, set the CH1 AUDIO SELECT switch
5
to “MANUAL”.
This control works regardless of the setting of the VCR
Setup Menu item No. 246 CH1 FRONT VR ENABLE.
To use this control, set the AUDIO LEVEL CH-1 audio
input level control (
7
on page 10) on the front section to
the maximum (10) position, or set the VCR Setup Menu
item No. 246 CH1 FRONT VR ENABLE to “DISABLE”.
3
[CH2 AUDIO LEVEL] CH2 audio input level control
Adjust the audio input level of the CH2 audio channel with
this control.
• This control is valid only when the CH2 AUDIO SELECT
switch
6
is set to "MANUAL".
4
[MONITOR SELECT] audio monitor selector switch
This switch is used to select the monitor sound output from
the monitoring loudspeaker
1
or via the EARPHONE jack
2
on page 22.
CH-1
: The CH1 channel audio is output.
MIX
: CH1 and CH2 channel audio are output mixed.
CH-2
: The CH2 channel audio is output.
5
[CH-1 AUDIO SELECT] selector switch
This switch is used to select the method for adjusting the
audio input level of the CH-1 audio channel.
The reference audio input level to the tape can be set using
No. 257 AUDIO REF. SIGNAL LEVEL in the VCR Setup
Menu screen (-20dB or -12dB).
☞
See page 74
AUTO
: The audio input level is held at the reference level
even when sounds greater than the reference
level are input.
The audio input level does not increase when
the input level is low.
MANUAL
: The audio input level can be adjusted with the
CH-1 AUDIO LEVEL control
2
or the CH-1
AUDIO LEVEL control
7
on page 10.
To use the AUDIO LEVEL CH-1 audio input level
control on the front section, set the VCR Setup
Menu item No. 246 CH1 FRONT VR ENABLE to
“ENABLE”.
6
[CH-2 AUDIO SELECT] selector switch
This switch is used to select the method for adjusting the
audio input level of the CH-2 audio channel.
The reference audio input level to the tape can be set using
No. 257 AUDIO REF. SIGNAL LEVEL in the VCR Setup
Menu screen (-20dB or -12dB).
☞
See page 74
AUTO
: The audio input level is held at the reference level
even when sounds greater than the reference
level are input.
The audio input level does not increase when
the input level is low.
MANUAL
: The audio input level can be adjusted with the
CH-2 AUDIO LEVEL control
3
.
7
[CH-1 AUDIO INPUT] selector switch
This switch is used to select the input section of the CH1
audio channel.
FRONT
: The sound from the AUDIO IN FRONT connector
on the front side section is input.
REAR
: The sound from the AUDIO IN REAR connector
on the rear side section is input.
8
[CH-2 AUDIO INPUT] selector switch
This switch is used to select the input section of the CH2
audio channel.
FRONT
: The sound from the AUDIO IN FRONT connector
on the front side section is input.
REAR
: The sound from the AUDIO IN REAR connector
on the rear side section is input.
[VCR Setting Section]
2-2 Right Side Section (Cont'd)
Make sure to move switches all the way. Do not leave a
switch stopped in a midway position. Noise will be
generated and operation irregularities will occur.
CAUTION:
