1
Mounting bracket removed from the car
Screws removed from the car in step
1
Mounting bracket removed from the car
Supplied screws
Supplied screws
Select the appropriate
type fitting to your audio
system space.
KW-AVX700
Installation/Connection Manual
0206MNMMDWJEIN
EN
© 2006 Victor Company of Japan, Limited
LVT1469-009A
[A]
This unit is designed to operate only on
12 V DC, NEGATIVE ground electrical systems
. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a
traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal
accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic
accident.
• The driver must not watch the monitor while driving.
If the driver watches the monitor while driving, it may lead to carelessness and cause an accident.
• If you need to operate the unit
while driving, be sure to look ahead carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback
picture will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake
system built in the car.
Notes on electrical connections
• Replace the fuse with one of the specified rating. If the fuse
blows frequently, consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 50 W at
the rear and 50 W at the front,
with an impedance of
4
Ω
to
8
Ω
.
•
Be sure to ground each unit to the car’s chassis.
• To prevent short-circuit, cover the terminals of the UNUSED leads
with insulating tape.
• The unit become very hot after use. Be careful not to get burned
when removing them.
TROUBLESHOOTING
•
The fuse blows.
* Are the red and black leads connected correctly?
•
Power cannot be turned on.
* Is the yellow lead connected?
•
No sound from the speakers.
* Is the speaker output lead short-circuited?
•
Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
•
Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
•
Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
Parts list for installation and connection
The following parts are provided for this unit.
If anything is missing, contact your dealer immediately.
Power cord
AV I/O cord
Main unit
Round head screws (M5 x 8 mm)
Flat head screws (M5 x 8 mm)
Crimps
Reverse gear signal extension cord
CR2025
Battery
RM-RK240
Remote controller
PRECAUTIONS on power supply and speaker connections:
•
DO NOT connect the speaker leads of the power cord to the car battery; otherwise,
the units will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the
speaker wiring in your car.
L
R
+
-
+
-
+
-
+
-
L
R
+
-
+
-
+
-
+
-
L
R
+
-
+
-
+
-
+
-
Required space for the monitor ejection
Install the unit at an angle of less than 30˚, taking it into account that the monitor would eject
when in use (see below).
30˚
Unit: mm
160
88.5
100
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, there is a possibility that parts could become loose or damaged.
• When tightening screws or bolts be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear panel to maintain proper ventilation when installed.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note:
Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Connect the power cord and AV I/O cord.
• See the reverse page for the power cord connection.
• See the reverse page for the AV I/O connection.
4
Install this unit using the screws removed in step
1
.
Note:
When installing the unit on the mounting bracket, make sure to use the supplied screws (M5 x 8 mm).
If longer screws are used, they could damage the unit.
The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.
Plate for use with a Nissan car
If necessary, restore the protruding tabs.
When installing the unit in a Nissan car
Plate for use with a Nissan car
Heat sink
