No.51781
1-37
DLA-M2000LU
DLA-M2000LE
64
Warning Messages
The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take
the corrective action described here.
Message
Cause
Corrective action
Page
• No device is connected to the
input terminal.
• The terminal is connected but no
signal is output from the
connected device.
* The selected input mode (input
terminal) name is shown in the
first line of the massage.
• Connect a device to the selected
terminal.
• Operate the connected device
and output a signal.
9, 11,
24 ~ 29,
32
• The frequency of the input video
signal is out of range.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals whose
frequency is within the projector’s
specifications.
22, 23,
66
• Though the frequency of the input
video signal is within the
acceptable range, other items
such as resolution are out of the
projector’s specifications.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals that
satisfies the projector’s
specifications.
22, 23,
66
• When the FREEZE button is
pressed, this message appears
for a few seconds.
• When a button not acceptable is
pressed during freezing, this
message appears for a few
seconds to notify that the image is
being frozen.
• To release freezing, press the
FREEZE button on the remote
control.
13, 36
• When the FREEZE button is
pressed for the video signals that
cannot be frozen (UXGA, etc.),
this message appears for a few
seconds to notify that the image
cannot be frozen.
* To forcibly clear the message,
press the ESCAPE button.
• Freeze function does not work for
the inputted video signals.
To use this function, input the
video signals that can be frozen.
13, 36
P C 1
N o i m a g e s i g n a l i s i n p u t t e d .
P C 1
F r e q u e n c y o f i m a g e s i g n a l i s o u t o f r a n g e .
P C 1
N o i m a g e s i g n a l i s s h o w n f o r t h i s t y p e .
FREEZE
FREEZE
65
Warning Messages
ENGLISH
DEUTSH
FRAN
Ç
AIS
ITALIANO
ESPA
Ñ
OL
Memo
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the
projector is bought. The display language can be selected from 6 languages. (Refer to page 45.) However, the input mode
(PC1, PC2,Y/C, VIDEO) and button indications (FREEZE, D.ZOOM, ESCAPE) are only displayed in English irrespective of
the display language setting.
The language settings in the section are explained in “English”.
• When the DIGITAL ZOOM button
is pressed for the video signals
that cannot be zoomed (UXGA,
etc.), this message appears for a
few seconds to notify that the
image cannot be digitally zoomed.
* To forcibly clear the message,
press the ESCAPE button.
• Digital-zoom function does not
work for the inputted video
signals.
To use the this function, input the
video signals that can be digitally
zoomed.
12, 36
• The accumulated lamp use time
reaches 900 hours.
* Every time the projector is turned
on, this message appears on the
screen.
• Press the ESCAPE button to
clear the massage.
(This display can be cleared with
the MENU button or other
buttons.)
• Arrange for a new light-source
lamp or replace the light-source
lamp a little earlier.
10, 12,
54 ,56
• The accumulated lamp use time
reaches 1000 hours.
The word “Warning” blinks.
* The message can be cleared by
pressing the ESCAPE button.
However, the same message will
appear every one hour.
* Once the projector is turned off,
the projector does not turn on
unless the light-source lamp is
replaced with new one.
* When the accumulated lamp use
time reaches 1010 hours, the
projector is forcibly shut off.
• Replace the light-source lamp
and reset the lamp use time.
56 ~ 59
Message
Cause
Corrective action
Page
D.ZOOM
ESCAPE
Lamp replacement
ESCAPE
Warning
Lamp replacement
