Juniper JUNOSe 10.3.1 Release Note Download Page 18

Page: 18 / 122

JUNOSe 10.3.1 Release Notes

Release Software Protocols

User Datagram Protocol (UDP) for IPv4 and IPv6

Network Management Protocols

Simple Network Management Protocol (SNMP) versions 1, 2c, and 3

Routing Protocols

Border Gateway Protocol (BGP-4)

Distance Vector Multicast Routing Protocol (DVMRP)

Internet Group Membership Protocol (IGMP)

Intermediate System–to–Intermediate System (IS-IS)

Layer 2 Virtual Private Networks (L2VPNs)

Mobile IP

Open Shortest Path First (OSPF) version 2 and version 3

Protocol Independent Multicast Protocol (PIM), including PIM dense mode, PIM
sparse mode, PIM dense-sparse mode, and PIM source-specific multicast

Routing Information Protocol (RIP) version 2

Virtual Private LAN Service (VPLS)

Virtual Router Redundancy Protocol (VRRP)

Multiprotocol Label Switching (MPLS)

Border Gateway Protocol (BGP-4)

Label Distribution Protocol (LDP)

Resource ReSerVation Protocol – Traffic Engineering Extensions (RSVP-TE)

Layer 2 Protocols

Asynchronous Transfer Mode (ATM)

Bridged Ethernet

Bridged IP

Cisco High-Level Data Link Control (Cisco HDLC)

Ethernet

Extensible Authentication Protocol (EAP)

Frame Relay

Summary of Contents for JUNOSe 10.3.1



























































































































Search results

Summary of Contents for JUNOSe 10.3.1

Reviews:

Related manuals for JUNOSe 10.3.1

Brands by name

Popular brands

Juniper JUNOSe 10.3.1, Release Note

Search results

Summary of Contents for JUNOSe 10.3.1

Reviews:

Related manuals for JUNOSe 10.3.1

Brands by name

Popular brands