Juniper EX4200 Series Hardware Manual Download Page 92

Page: 92 / 344

Documentation

Chassis Physical Specifications for EX4200 Switches on page 9

•

Rack-Mounting and Cabinet-Mounting Warnings on page 280

•

Clearance Requirements for Airflow and Hardware Maintenance for EX4200 Switches
on page 72

•

Mounting an EX4200 Switch on Two Posts in a Rack or Cabinet on page 160

•

Mounting an EX4200 Switch on Four Posts in a Rack or Cabinet on page 163

•

Mounting an EX4200 Switch in a Recessed Position in a Rack or Cabinet on page 166

Cabinet Requirements for EX4200 Switches

You can mount the switch in a cabinet that contains a 19-in. rack.

Cabinet requirements consist of:

•

Cabinet size

•

Clearance requirements

•

Cabinet airflow requirements

Table 34 on page 70

provides the cabinet requirements and specifications for the switch.

Table 34: Cabinet Requirements and Specifications for the Switch

Guidelines

Cabinet
Requirement

•

You can mount the switch in a cabinet that contains a 19-in. rack as defined in

Cabinets, Racks,

Panels, and Associated Equipment

(document number EIA-310–D) published by the Electronics

Industry Association (

http://www.ecianow.org/standards-practices/standards/

) .

•

The minimum cabinet size must be able to accommodate the maximum external dimensions of the
switch.

Cabinet size

•

The outer edges of the mounting brackets extend the width of the chassis to 19 in. (48.2 cm).

•

The minimum total clearance inside the cabinet is 30 in. (76.2 cm) between the inside of the front
door and the inside of the rear door.

Cabinet clearance

EX4200 Switch Hardware Guide

Summary of Contents for EX4200 Series




























































































































































































































































































































Search results

Summary of Contents for EX4200 Series

Reviews:

Juniper EX4200 Series, Hardware Manual, Page: 92 / 344

Search results

Summary of Contents for EX4200 Series

Reviews: