manualshive.com logo in svg

Juniper EX4200 Series, Hardware Manual, Page: 325 / 344

Share
Download
Juniper EX4200 Series Hardware Manual Download Page 325

•

See

EX9214 Switch Hardware Overview

for the ESD point location.

•

See

OCX1100 Switches Hardware Overview

for the ESD point location.

•

See

QFX3008-I Interconnect Device Overview

for the ESD point location.

•

See

Front Panel of a QFX3500 Device

for the ESD point location.

•

See

Front Panel of a QFX3600 Device

for the ESD point location.

•

See

Physical Description of a Redundant Power System

•

See

Port Panel of an EX4600 Switch

for the ESD point location.

•

See

Port Panel of a QFX5100-48S Device

for the ESD point location.

•

See

Port Panel of a QFX5100-24Q Device

for the ESD point location.

•

See

Port Panel of a QFX5100-96S Device

for the ESD point location.

AC Power Electrical Safety Guidelines

This topic applies to hardware devices in the EX Series product family, which includes
EX Series switches, the EX Series Redundant Power System (RPS), and the XRE200
External Routing Engine.

This topic also applies to hardware devices in the QFX Series and to OCX1100 switches.

CAUTION:

For devices with AC power supplies, an external surge protective

device (SPD) must be used at the AC power source.

The following electrical safety guidelines apply to AC-powered devices:

•

Note the following warnings printed on the device:

“

CAUTION:

THIS UNIT HAS MORE THAN ONE POWER SUPPLY CORD. DISCONNECT

ALL POWER SUPPLY CORDS BEFORE SERVICING TO AVOID ELECTRIC SHOCK.”

“

ATTENTION:

CET APPAREIL COMPORTE PLUS D'UN CORDON D'ALIMENTATION.

AFIN DE PRÉVENIR LES CHOCS ÉLECTRIQUES, DÉBRANCHER TOUT CORDON
D'ALIMENTATION AVANT DE FAIRE LE DÉPANNAGE.”

•

AC-powered devices are shipped with a three-wire electrical cord with a grounding-type
plug that fits only a grounding-type power outlet. Do not circumvent this safety feature.
Equipment grounding must comply with local and national electrical codes.

•

You must provide an external certified circuit breaker rated minimum 20 A in the building
installation.

•

The power cord serves as the main disconnecting device for the AC-powered device.
The socket outlet must be near the AC-powered device and be easily accessible.

•

For devices that have more than one power supply connection, you must ensure that
all power connections are fully disconnected so that power to the device is completely

303

Copyright © 2015, Juniper Networks, Inc.

Chapter 31: Electrical Safety Guidelines and Warnings

Summary of Contents for EX4200 Series

























































































































































































































































































































































Reviews:

No comments