Juniper EX4200 Series Hardware Manual Download Page 83

Page: 83 / 344

CHAPTER 6

Preparation Overview

•

Site Preparation Checklist for EX4200 Switches on page 61

•

Environmental Requirements and Specifications for EX Series Switches on page 63

•

General Site Guidelines on page 66

•

Site Electrical Wiring Guidelines on page 67

•

Rack Requirements for EX4200 Switches on page 69

•

Cabinet Requirements for EX4200 Switches on page 70

•

Requirements for Mounting an EX4200 Switch on a Desktop or Wall on page 71

•

Clearance Requirements for Airflow and Hardware Maintenance for EX4200
Switches on page 72

Site Preparation Checklist for EX4200 Switches

The checklist in

Table 30 on page 61

summarizes the tasks you need to perform when

preparing a site for EX4200 switch installation.

Table 30: Site Preparation Checklist

Date

Performed by

For More Information

Item or Task

Environment

“Environmental Requirements and
Specifications for EX Series Switches”
on page 63

Verify that environmental factors such as
temperature and humidity do not exceed switch
tolerances.

Power

Measure distance between external power
sources and switch installation site.

Locate sites for connection of system
grounding.

“Power Specifications for EX4200
Switches” on page 75

Calculate the power consumption and
requirements.

Hardware Configuration

Summary of Contents for EX4200 Series




























































































































































































































































































































Search results

Summary of Contents for EX4200 Series

Reviews:

Juniper EX4200 Series, Hardware Manual, Page: 83 / 344

Search results

Summary of Contents for EX4200 Series

Reviews: