manualshive.com logo in svg

Juniper EX4200 Series, Hardware Manual, Page: 328 / 344

Share
Download
Juniper EX4200 Series Hardware Manual Download Page 328

Related

Documentation

General Safety Guidelines and Warnings on page 267

•

•

General Electrical Safety Guidelines and Warnings on page 299

•

AC Power Electrical Safety Guidelines on page 303

DC Power Electrical Safety Guidelines

This topic applies to hardware devices in the EX Series product family, which includes
EX Series switches and the XRE200 External Routing Engine.

This topic also applies to hardware devices in the QFX Series and to OCX1100 switches.

•

A DC-powered device is equipped with a DC terminal block that is rated for the power
requirements of a maximally configured device.

NOTE:

To supply sufficient power, terminate the DC input wiring on a facility

DC source that is capable of supplying:

•

Minimum of 7.5 A at –48 VDC for EX2200 and EX3300 switches

•

Minimum of 8 A at –48 VDC for EX3200 and EX4200 switches

•

Minimum of 20 A at –48 VDC for EX4300, EX4500, and EX4550 switches

•

Minimum of 50 A at –48 VDC for EX6210 switches

•

Minimum of 60 A at –48 VDC for EX8208 switches

•

Minimum of 100 A at –48 VDC for EX8216 switches

•

Minimum of 7 A at –48 VDC for QFX3500, EX4600, and QFX5100 devices

•

Minimum of 8 A at –48 VDC for QFX3600 devices

•

Minimum of 7 A at –48 VDC for OCX1100 switches

Incorporate an easily accessible disconnect device into the facility wiring. Be sure to
connect the ground wire or conduit to a solid office earth ground. A closed loop ring is
recommended for terminating the ground conductor at the ground stud.

•

Run two wires from the circuit breaker box to a source of 48 VDC.

•

A DC-powered device that is equipped with a DC terminal block is intended only for
installation in a restricted access location. In the United States, a restricted access
area is one in accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical
Code ANSI/NFPA 70.

NOTE:

Primary overcurrent protection is provided by the building circuit

breaker. This breaker must protect against excess currents, short circuits,
and earth grounding faults in accordance with NEC ANSI/NFPA 70.

Copyright © 2015, Juniper Networks, Inc.

306

EX4200 Switch Hardware Guide

Summary of Contents for EX4200 Series

























































































































































































































































































































































Reviews:

No comments