manualshive.com logo in svg

Juniper EX4200 Series, Hardware Manual, Page: 292 / 344

Share
Download
Juniper EX4200 Series Hardware Manual Download Page 292

que entraña la corriente eléctrica y familiarizarse con los procedimientos
estándar de prevención de accidentes.

Varning!

Denna varningssymbol signalerar fara. Du befinner dig i en situation

som kan leda till personskada. Innan du utför arbete på någon utrustning
måste du vara medveten om farorna med elkretsar och känna till vanligt
förfarande för att förebygga skador.

Related

Documentation

General Safety Guidelines and Warnings on page 267

•

•

Installation Instructions Warning on page 275

•

Maintenance and Operational Safety Guidelines and Warnings on page 293

•

Grounded Equipment Warning on page 284

•

Laser and LED Safety Guidelines and Warnings for Switches on page 287

•

Laser and LED Safety Guidelines and Warnings for the QFX Series

•

Warning Statement for Norway and Sweden on page 271

Qualified Personnel Warning

This topic applies to hardware devices in the EX Series product family, which includes
EX Series switches, the EX Series Redundant Power System (RPS), and the XRE200
External Routing Engine.

This topic also applies to hardware devices in the QFX Series and to OCX1100 switches.

WARNING:

Only trained and qualified personnel should install or replace the

device.

Waarschuwing

Installatie en reparaties mogen uitsluitend door getraind en

bevoegd personeel uitgevoerd worden.

Varoitus

Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai vaihtaa

tämän laitteen.

Attention

Tout installation ou remplacement de l'appareil doit être réalisé

par du personnel qualifié et compétent.

Warnung

Gerät nur von geschultem, qualifiziertem Personal installieren oder

auswechseln lassen.

Avvertenza

Solo personale addestrato e qualificato deve essere autorizzato

ad installare o sostituire questo apparecchio.

Advarsel

Kun kvalifisert personell med riktig opplæring bør montere eller

bytte ut dette utstyret.

Copyright © 2015, Juniper Networks, Inc.

270

EX4200 Switch Hardware Guide

Summary of Contents for EX4200 Series

























































































































































































































































































































































Reviews:

No comments