Jungheinrich ese 20, Operating Instructions Manual

Page: 17 / 53

C 2
0499
.G
B
3 Moving the truck with the drive unit inoperative
f
This operating mode is not permitted when negotiating inclines and gradients.
If the truck has to be moved after a failure has rendered it immobile, proceed as
follows:
- Set the master switch to position “OFF”.
- Set the key switch to position “OFF” (“0”) and
remove the key.
- Ensure that the truck cannot accidentally
move.
- Remove the drive cover (5) and put it aside.
- Slacken the lock nuts (4) and tighten the
screws (3).
The brake has now been released and the truck
can be moved.
f
After arriving at the repair bay, ensure that the
brake is put back to its initial state. The truck
must on no account be parked with the brake in
the released condition.
- Loosen the screws (3) by approx. 5 mm and
lock by tightening the lock nuts (4).
The brake is now applied again.
- Mount the drive cover (5).
4
3
4
3
5
C 2
0499
.G
B
3 Moving the truck with the drive unit inoperative
f
This operating mode is not permitted when negotiating inclines and gradients.
If the truck has to be moved after a failure has rendered it immobile, proceed as
follows:
- Set the master switch to position “OFF”.
- Set the key switch to position “OFF” (“0”) and
remove the key.
- Ensure that the truck cannot accidentally
move.
- Remove the drive cover (5) and put it aside.
- Slacken the lock nuts (4) and tighten the
screws (3).
The brake has now been released and the truck
can be moved.
f
After arriving at the repair bay, ensure that the
brake is put back to its initial state. The truck
must on no account be parked with the brake in
the released condition.
- Loosen the screws (3) by approx. 5 mm and
lock by tightening the lock nuts (4).
The brake is now applied again.
- Mount the drive cover (5).
4
3
4
3
5
C 2
0499
.G
B
3 Moving the truck with the drive unit inoperative
f
This operating mode is not permitted when negotiating inclines and gradients.
If the truck has to be moved after a failure has rendered it immobile, proceed as
follows:
- Set the master switch to position “OFF”.
- Set the key switch to position “OFF” (“0”) and
remove the key.
- Ensure that the truck cannot accidentally
move.
- Remove the drive cover (5) and put it aside.
- Slacken the lock nuts (4) and tighten the
screws (3).
The brake has now been released and the truck
can be moved.
f
After arriving at the repair bay, ensure that the
brake is put back to its initial state. The truck
must on no account be parked with the brake in
the released condition.
- Loosen the screws (3) by approx. 5 mm and
lock by tightening the lock nuts (4).
The brake is now applied again.
- Mount the drive cover (5).
4
3
4
3
5
C 2
0499
.G
B
3 Moving the truck with the drive unit inoperative
f
This operating mode is not permitted when negotiating inclines and gradients.
If the truck has to be moved after a failure has rendered it immobile, proceed as
follows:
- Set the master switch to position “OFF”.
- Set the key switch to position “OFF” (“0”) and
remove the key.
- Ensure that the truck cannot accidentally
move.
- Remove the drive cover (5) and put it aside.
- Slacken the lock nuts (4) and tighten the
screws (3).
The brake has now been released and the truck
can be moved.
f
After arriving at the repair bay, ensure that the
brake is put back to its initial state. The truck
must on no account be parked with the brake in
the released condition.
- Loosen the screws (3) by approx. 5 mm and
lock by tightening the lock nuts (4).
The brake is now applied again.
- Mount the drive cover (5).
4
3
4
3
5