Jungheinrich EJC 14, Operating Instructions Manual

Page: 52 / 55

F 9
0401
.GB
6.4 Check hydraulic oil level
– Prepare the truck for servicing and maintenance operations (refer to chapter F, sec-
tion 6.1).
– Open the front hood (see section 6.3).
– Check the hydraulic oil level of the hydraulic tank (see section 5).
A
There are markings on the hydraulic tank (see section 5). The oil level must be chek-
ked with the lifting device being lowered.
– If required, top up with hydraulic oil with the required characteristics
(see section 6.4; see table)
A
Mounting is performed in reverse order.
6.5 Check the transmission oil level
– Prepare the truck for servicing and maintenance operations (see section 6.3).
– Open the front hood (see section 6.2).
– Loosen 2 x screws (5) using the key (2).
– Remove carefully the wheel cover (4).
– Check gear-oil level - oil level must reach the filler neck
(see section 5).
– If required, top up with gear oil with the required characteristics (see section 5).
A
Mounting is performed in reverse order.
6.6 Exchanging the coarse sieve
– Preparation of the truck for servicing
and maintenance operations
(refer to chapter F, section 6.1).
– Open the front hood (see section 6.2).
– Loosen the screwed connection (6).
– Pull off the connection (7) and remove
the coarse sieve.
– Insert a new coarse sieve.
A
Mounting is performed in reverse order.
A
Tighten screwed connection (6) with
max. 60
+10
Nm.
Marking Litre Lifting heights (h
3
)
E ZT ZZ DZ
Upper edge approx. 10.5 - - - up to 5350
4 approx. 10 - - - -
3 approx. 8.3 - - up to 4300 up to 4300
2 approx. 6.8 - up to 4300 up to 3600 -
1 approx. 5.1 all up to 3200 up to 2500 -
6 7
F 9
0401
.GB
6.4 Check hydraulic oil level
– Prepare the truck for servicing and maintenance operations (refer to chapter F, sec-
tion 6.1).
– Open the front hood (see section 6.3).
– Check the hydraulic oil level of the hydraulic tank (see section 5).
A
There are markings on the hydraulic tank (see section 5). The oil level must be chek-
ked with the lifting device being lowered.
– If required, top up with hydraulic oil with the required characteristics
(see section 6.4; see table)
A
Mounting is performed in reverse order.
6.5 Check the transmission oil level
– Prepare the truck for servicing and maintenance operations (see section 6.3).
– Open the front hood (see section 6.2).
– Loosen 2 x screws (5) using the key (2).
– Remove carefully the wheel cover (4).
– Check gear-oil level - oil level must reach the filler neck
(see section 5).
– If required, top up with gear oil with the required characteristics (see section 5).
A
Mounting is performed in reverse order.
6.6 Exchanging the coarse sieve
– Preparation of the truck for servicing
and maintenance operations
(refer to chapter F, section 6.1).
– Open the front hood (see section 6.2).
– Loosen the screwed connection (6).
– Pull off the connection (7) and remove
the coarse sieve.
– Insert a new coarse sieve.
A
Mounting is performed in reverse order.
A
Tighten screwed connection (6) with
max. 60
+10
Nm.
Marking Litre Lifting heights (h
3
)
E ZT ZZ DZ
Upper edge approx. 10.5 - - - up to 5350
4 approx. 10 - - - -
3 approx. 8.3 - - up to 4300 up to 4300
2 approx. 6.8 - up to 4300 up to 3600 -
1 approx. 5.1 all up to 3200 up to 2500 -
6 7