Jungheinrich EJB 14, Operating Instructions Manual

Page: 49 / 49

099
9.G
B
F 12
7.11 Recommissioning the truck
– Thoroughly clean the truck.
– Grease the truck as detailed in the lubrication chart (see section 5).
– Clean the battery. Grease the terminal screws using pole grease and reconnect the
battery.
– Recharge the battery (see chapter D).
– Check if the transmission oil contains condensed water and change, if required.
– Check if the hydraulic oil contains condensed water and change, if required.
– Start up the truck (see to chapter E).
A
For battery-driven trucks:
If switching troubles are experienced in the electric system, spray the exposed con-
tacts
with contact spray and remove any oxide layer on the contacts of the control equip-
ment by operating it several times.
A
Upon recommissioning of the truck perform several brake tests immediately.
8 Safety checks to be performed at regular intervals and following any untoward
incidents
(
D
: UVV according to VBG 36)
At least once yearly, or after any untoward incident, the truck has to be checked by a
qualified inspector. The inspector must assess the condition of the truck from a stand-
point purely concerned with safety aspects, uninfluenced by any company or econo-
mic circumstances. The inspector must be adequately informed and experienced to
be able to assess the condition of the truck and the effectiveness of the safety instal-
lations based on the technical rules and principles governing the inspection of trucks.
The inspection must comprise a comprehensive check of the technical condition of
the fork-lift truck with regard to accident prevention aspects. Apart from this, the floor
conveyor must be thoroughly inspected for damage possibly caused by inappropriate
use. The inspection results must be recorded in an inspection report. The report must
be kept available for a period spanning at least the next two inspection intervals.
The user has to ensure that all defects are eliminated without delay.
A
The manufacturer has set up a special safety service with adequately qualified staff.
As visual proof that the truck has passed the safety inspection, a plaque will be affixed
to it. This plaque indicates in which month of which year the next test will be due.
099
9.G
B
F 12
7.11 Recommissioning the truck
– Thoroughly clean the truck.
– Grease the truck as detailed in the lubrication chart (see section 5).
– Clean the battery. Grease the terminal screws using pole grease and reconnect the
battery.
– Recharge the battery (see chapter D).
– Check if the transmission oil contains condensed water and change, if required.
– Check if the hydraulic oil contains condensed water and change, if required.
– Start up the truck (see to chapter E).
A
For battery-driven trucks:
If switching troubles are experienced in the electric system, spray the exposed con-
tacts
with contact spray and remove any oxide layer on the contacts of the control equip-
ment by operating it several times.
A
Upon recommissioning of the truck perform several brake tests immediately.
8 Safety checks to be performed at regular intervals and following any untoward
incidents
(
D
: UVV according to VBG 36)
At least once yearly, or after any untoward incident, the truck has to be checked by a
qualified inspector. The inspector must assess the condition of the truck from a stand-
point purely concerned with safety aspects, uninfluenced by any company or econo-
mic circumstances. The inspector must be adequately informed and experienced to
be able to assess the condition of the truck and the effectiveness of the safety instal-
lations based on the technical rules and principles governing the inspection of trucks.
The inspection must comprise a comprehensive check of the technical condition of
the fork-lift truck with regard to accident prevention aspects. Apart from this, the floor
conveyor must be thoroughly inspected for damage possibly caused by inappropriate
use. The inspection results must be recorded in an inspection report. The report must
be kept available for a period spanning at least the next two inspection intervals.
The user has to ensure that all defects are eliminated without delay.
A
The manufacturer has set up a special safety service with adequately qualified staff.
As visual proof that the truck has passed the safety inspection, a plaque will be affixed
to it. This plaque indicates in which month of which year the next test will be due.