background image

4 Automatic switch standard operation 

Switch on the light via extension 

A 2-wire extension or an installation button, NO contact is connected. 

Press extension or installation button. 
Light is switched on independently of the brightness. Automatic mode is active. 

Manual switch-on is not possible. 

Setting the brightness threshold 

The brightness threshold is infinitely adjustable in a range from approx. 0 to 80 lux and 
day operation

3

. In so doing, the 

3

symbol stands for brightness-independent switching and the 

2

symbol for switching in case of darkness. 

Remove plate (4) (picture 1). 

Turn the adjuster (6) to the required position (picture 2).  

Should the motion detector no longer react to detected movements in Night mode, 

2

setting, turn the adjuster back somewhat towards 

3

Snap cover on. 

Setting the sensitivity 

The sensitivity of the cover is infinitely adjustable using the adjuster 

Sens.

 (5). 

Remove plate (4) (picture 1). 

Set the sensitivity using the adjuster 

Sens.

 (5). 

Snap cover on. 

5 Automatic switch universal operation 

Switch on the light via extension 

A 2-wire extension or an installation button, NO  contact is connected. 

Press button for less than 0.4 seconds. 
The Light is switched on independently of the brightness for the run-on time. 

If the run-on time setting dial (5) is set to 

M

, Short-time operation (picture 6), then the light 

is switched on for approx. 0.5 seconds, even if the button is pressed for longer. 

Manual switch-on is not possible. 

Switch light on with minimum brightness 

Motion detector cover is combined with a dimmer insert.  
A 2-wire extension is connected. 
Light is switched off 

Press button at bottom for longer than 0.4 seconds. 
Light is switched on at minimum brightness and stays at this brightness for as long as 
motion is detected. 

Adjusting brightness via extension 

Motion detector cover is combined with a dimmer insert.  
A 2-wire extension is connected. 

Press top button for a long time. 
The light gets brighter up to maximum brightness. 

Long press on bottom of button. 
Light gets darker to minimum brightness. 

4/14 

32540233 
J:0082540233 

26.07.2010 

Light Management  

Automatic switch 180° 1.10 m 

Summary of Contents for 1180 Series















Reviews: