background image

 
 
 
 

 
 
 

 

4 / 13 

 

JUNG ANTRIEBSTECHNIK U. AUTOMATION GMBH 

 Felsweg 18 

 35435 Wettenberg 

 Germany 

Tel.: +49-(0)641-48017-0 

 Fax: +49-(0)641-48017-15 

 eMail: [email protected] 

 www.ja2-gmbh.de 

 

1.3 

Warranty & Liability 

 

 
As manufacturer of linear motor systems, JA² GmbH does not accept 
responsibility for the improper use, application or handling of products and 
declines any liability. Warranty may not be claimed after use or combination 
with third party products, like cables and power supplies. With purchase 
every customer confirms to have read and understood the in the installation 
and maintenance guide listed warnings. This guide is included in every 
delivery and available online. Please always include this guide in your 
deliveries, should you resell our linear motor systems as components or 
install them into machines. We also refer to our general terms and 
conditions. 
 

 

1.4 

Copyright & Trademark Protection 

 

 
This work is protected by copyright. 
All rights reserved! 
Product names, as well as word and figurative marks are registered 
trademarks. 
 

 

 

 
We hereby give permission to reproduce and distribute this work for machine 
documentation purposes or under the use of electronic systems. However, 
we expressly point out, that this document is not subject to our updating 
service. Technical changes reserved. 
 

 

Summary of Contents for HM01-23














Reviews: